Related Experiment Video

Updated: Apr 16, 2026

Shrinkage of Dental Composite in Simulated Cavity Measured with Digital Image Correlation
08:45

Shrinkage of Dental Composite in Simulated Cavity Measured with Digital Image Correlation

Published on: July 21, 2014

14.1K

Comparative analysis of polymerization shrinkage of different resin composites

Iana Coutinho Barretto, Luana Farias Pontes, Karina Kato Carneiro

    General Dentistry
    |March 4, 2015
    PubMed

    Keywords:
    curing lightsdental materialspolymerization

    More Related Videos

    Stereolithographic 3D Printing with Renewable Acrylates08:28

    Stereolithographic 3D Printing with Renewable Acrylates

    Published on: September 12, 2018

    10.0K
    The Effect of Construction and Demolition Waste Plastic Fractions on Wood-Polymer Composite Properties09:06

    The Effect of Construction and Demolition Waste Plastic Fractions on Wood-Polymer Composite Properties

    Published on: June 7, 2020

    8.6K

    Related Concept Videos

    Shrinkage in Concrete01:27

    Shrinkage in Concrete

    Shrinkage in concrete is primarily due to water loss from evaporation, hydration of cement, or carbonation, leading to a reduction in volume. The volumetric contraction results in volumetric strain in concrete. However, in practice, shrinkage is measured as linear strain, which is one-third of the volumetric strain.
    When concrete is still in its plastic state, it can undergo a decrease in volume by about 1% of its absolute volume. This decrease is known as plastic shrinkage. It arises either...
    542
    Drying Shrinkage01:21

    Drying Shrinkage

    When hardened concrete is exposed to air with a relative humidity of less than 100 percent, it begins to lose the free water within its capillaries. As this water evaporates, the water initially adsorbed onto the calcium silicate hydrates migrates towards these now empty spaces and eventually evaporates as well. Over time, as more water leaves, the volume of the concrete decreases, a phenomenon known as drying shrinkage.
    A portion of this drying shrinkage can be reversed; if the concrete is...
    477
    Molecular Weight of Step-Growth Polymers01:08

    Molecular Weight of Step-Growth Polymers

    Step growth polymerization involves bi or multifunctional monomers. Bifunctional monomers react to form linear step growth polymers, whereas multifunctional monomers react to form non-linear or branched polymers.
    As the step-growth polymerization involves step-wise condensation of monomers, the molecular weight also builds up eventually. Consequently, high molecular weight polymers are obtained at the late stages of the polymerization, where 99% of monomers have been consumed.
    The extent of the...
    3.0K
    Polymer Classification: Stereospecificity01:26

    Polymer Classification: Stereospecificity

    Polymerization generates chiral centers along the entire backbone of a polymer chain. Accordingly, the stereochemistry of the substituent group has a significant effect on polymer properties. Polymers formed from monosubstituted alkene monomers feature chiral carbons at every alternate position in the polymer backbone. Relative to the predominant orientation of substituents at the adjacent chiral carbons, the polymer can exist in three different configurations: isotactic, syndiotactic, and...
    3.5K
    Polymers: Molecular Weight Distribution01:10

    Polymers: Molecular Weight Distribution

    For any given polymer, the weight average molecular weight (Mw) is higher than, if not equal to, the number average molecular weight (Mn). The only situation in which the weight average molecular weight and the number average molecular weight are equal is when a polymer consists only of chains with equal molecular weight. However, this never happens in a synthetic polymer, since it is difficult to control the polymerization process up to a molecular level with accuracy to a hundred percent.
    5.3K
    Polymer Classification: Architecture01:14

    Polymer Classification: Architecture

    Polymers are classified as linear or branched on the basis of their chain architecture. The polymer chains in linear polymers have a long chain-like structure with minimal to no branching at all. Even if a polymer features large substituent groups on the monomer, which appear as branches to the skeleton, it is not considered a branched polymer. A branched polymer contains secondary polymer chains that arise from the main polymer chain. The branching occurs when the polymer growth shifts from...
    4.2K