Related Experiment Video

Updated: Apr 15, 2026

Ultrasound Velocity Measurement in a Liquid Metal Electrode
08:41

Ultrasound Velocity Measurement in a Liquid Metal Electrode

Published on: August 5, 2015

12.3K

An ultrasound-based liquid pressure measurement method in small diameter pipelines considering the installation and

Xue Li1, Zhengxiang Song2

  • 1State Key Laboratory of Electrical Insulation and Power Equipment, Xi'an Jiaotong University, Xi'an 710049, China. lixue28@stu.xjtu.edu.cn.

Sensors (Basel, Switzerland)
|April 11, 2015
PubMed

More Related Videos

The Measurement of Unsteady Surface Pressure Using a Remote Microphone Probe08:53

The Measurement of Unsteady Surface Pressure Using a Remote Microphone Probe

Published on: December 3, 2016

7.5K
Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow08:25

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow

Published on: April 30, 2018

7.8K

Related Concept Videos

Measurement of Fluid Pressure01:16

Measurement of Fluid Pressure

Fluid pressure is commonly measured using devices called manometers, which rely on liquid columns to indicate pressure differences. The height of a liquid column in a manometer reflects the pressure exerted by the fluid, providing a simple yet effective means of measurement. Different types of manometers serve specific purposes based on their configurations and the type of fluids involved.
A basic form of manometer is the piezometer, a vertical tube open at the top and filled with the same...
2.2K
Pipe Flowrate Measurement01:28

Pipe Flowrate Measurement

In pipe flow measurement, orifice, nozzle, and Venturi meters are commonly used to determine fluid flowrates by constricting the flow area, which increases fluid velocity and reduces pressure. This pressure difference, governed by Bernoulli's principle and adjusted for real-world conditions, is essential for calculating flowrate. Each meter type is suited to specific applications based on accuracy, efficiency, and compatibility with various flow conditions.
The orifice meter is a simple,...
1.6K
Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
885
Pipe Flowrate Measurement: Problem Solving01:28

Pipe Flowrate Measurement: Problem Solving

A spray tank system is engineered to uniformly distribute a pest-control liquid across plants by using a pressurized mechanism. The tank, pressurized to 150 kPa, holds the pesticide at a height of 0.80 meters. Liquid flows from the tank through a 1.9 meter pipe with a diameter of 0.015 meters, angled at 0.698 radians, ultimately reaching a 0.007 meter nozzle that sprays the pesticide. Accurate calculation of the system's flow rate is crucial to ensure uniform application, and this is achieved...
1.0K
Design Example: Flow of Oil Through Circular Pipes01:25

Design Example: Flow of Oil Through Circular Pipes

Understanding fluid flow behavior through pipes is critical in fluid mechanics, especially in applications like oil transportation through pipelines. Hagen-Poiseuille's law provides an exact solution derived from the Navier-Stokes equations for steady, incompressible, and laminar flow within a circular pipe. Hagen-Poiseuille's law helps determine the necessary pressure drop across a pipeline section by determining parameters like pipe length, radius, oil viscosity, and the desired volumetric...
563
Major Losses in Pipes01:28

Major Losses in Pipes

When a fluid flows through a pipe, it experiences energy losses due to frictional resistance along the pipe walls, known as major losses. These energy losses result in a pressure drop, which varies based on the flow conditions — whether laminar or turbulent — and the specific physical properties of the fluid and pipe.
Fluid flow can be classified as laminar or turbulent, primarily based on the Reynolds number. This dimensionless number reflects the relative influence of inertial to...
2.7K