Related Experiment Video

Updated: Apr 6, 2026

Fabrication and Characterization of Superconducting Resonators
10:26

Fabrication and Characterization of Superconducting Resonators

Published on: May 21, 2016

12.1K

High-gain cryogenic amplifier assembly employing a commercial CMOS operational amplifier

J E Proctor1, A W Smith2, T M Jung1

  • 1Jung Research and Development Corp., 3807 Porter St. NW #304, Washington, DC 20016, USA.

The Review of Scientific Instruments
|August 3, 2015
PubMed

More Related Videos

Cryogenic Liquid Jets for High Repetition Rate Discovery Science08:34

Cryogenic Liquid Jets for High Repetition Rate Discovery Science

Published on: May 9, 2020

3.6K
Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping14:58

Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping

Published on: June 3, 2015

15.5K

Related Concept Videos

MOSFET Amplifiers01:17

MOSFET Amplifiers

The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
684
Operational Amplifiers01:17

Operational Amplifiers

The operational amplifier, often referred to as an op-amp, is a multifaceted building block of a circuit. This electronic component functions like a voltage-controlled voltage source and can also be used to create a voltage- or current-controlled current source. The design of an operational amplifier enables it to execute mathematical operations when external components like resistors and capacitors are linked to its terminals. An op-amp has the capacity to sum signals, amplify a signal,...
2.2K
Cascaded Op Amps01:16

Cascaded Op Amps

Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
1.3K
Design Example: Vintage Mixing Console01:17

Design Example: Vintage Mixing Console

A sound engineer at a music company recently encountered a problem. The output from their newly acquired studio's vintage mixing console was too low for the requirements of modern recording equipment. To rectify this situation, the engineer decided to design an audio pre-amplifier using an operational amplifier (op-amp) to boost the signal level.
The specifications for the pre-amplifier were clear. It needed to amplify the audio signal by a factor of 10, have an input impedance above 10...
658
Small-Signal Analysis of MOSFET Amplifiers01:23

Small-Signal Analysis of MOSFET Amplifiers

In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
1.3K
Characteristics of Practical Op Amps01:16

Characteristics of Practical Op Amps

A difference amplifier, a crucial component in numerous electronic devices, ideally amplifies only the difference-mode signal, which is the difference between two input signals. However, in practical circuits, the output voltage depends on both the differential gain and the common-mode gain.
The ratio of differential gain to the common-mode gain is defined as the common-mode rejection ratio (CMRR). This ratio quantifies the ability of operational amplifiers (op-amps) to reject common-mode...
957