Related Experiment Video

Updated: Apr 1, 2026

Visualizing Uniaxial-strain Manipulation of Antiferromagnetic Domains in Fe1+YTe Using a Spin-polarized Scanning Tunneling Microscope
09:06

Visualizing Uniaxial-strain Manipulation of Antiferromagnetic Domains in Fe1+YTe Using a Spin-polarized Scanning Tunneling Microscope

Published on: March 24, 2019

8.7K

Thermal surface free energy and stress of iron

Stephan Schönecker1, Xiaoqing Li1, Börje Johansson1,2

  • 1Applied Materials Physics, Department of Materials Science and Engineering, Royal Institute of Technology, Stockholm SE-10044, Sweden.

Scientific Reports
|October 7, 2015
PubMed

More Related Videos

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes11:05

Knowledge Based Cloud FE Simulation of Sheet Metal Forming Processes

Published on: December 13, 2016

12.8K
Determining the Mechanical Strength of Ultra-Fine-Grained Metals05:04

Determining the Mechanical Strength of Ultra-Fine-Grained Metals

Published on: November 22, 2021

2.7K

Related Concept Videos

Thermal Stress01:09

Thermal Stress

If the temperature of an object is changed while it is prevented from expanding or contracting, the object is subjected to stress. The stress is compressive if the object expands in the absence of constraint and tensile if it contracts. This stress resulting from temperature change is known as thermal stress. It can be quite large and can cause damage. To avoid this stress, engineers may design components so they can expand and contract freely. For instance, on highways, gaps are deliberately...
3.6K
Frictional Force01:07

Frictional Force

When a body is in motion, it encounters resistance because the body interacts with its surroundings. This resistance is known as friction, a common yet complex force whose behavior is still not completely understood. Friction opposes relative motion between systems in contact, but also allows us to move. Friction arises in part due to the roughness of surfaces in contact. For one object to move along a surface, it must rise to where the peaks of the surface can skip along the bottom of the...
10.7K
Surface Tension and Surface Energy01:16

Surface Tension and Surface Energy

When a paint brush is immersed in water, the bristles wave freely inside the water. When it is taken out, the bristles stick together. The reason behind this effect is surface tension.
Consider a beaker filled with liquid. The bulk molecules in the liquid experience equal attractive forces on all sides with the surrounding molecules. However, the surface molecules experience a net attractive force downward due to the bulk molecules. The surface of the liquid behaves like a stretched membrane,...
3.5K
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
637
Shearing Stress01:18

Shearing Stress

Shearing stress, denoted by the Greek letter tau (τ), is stress caused by forces acting transversely on an object. These forces create internal ones within the entity in the plane where the external forces are applied. The resultant of these internal forces is the shear in the section.
The average shearing stress can be calculated by dividing the shear by the area of the cross-section.
2.6K
General State of Stress01:21

General State of Stress

The general state of stress within a material can be accurately depicted using a stress tensor. This tensor encapsulates the internal forces distributed within a material subjected to external forces or deformations.
Specifically, consider a tetrahedral element where one face, labeled XYZ, is perpendicular to the line OA, and the remaining faces align with the coordinate axes with point O as the origin. At any point, such as point O, the stress tensor can be used to determine the stress...
836