Elbow- and hinge-bending motions of IgG: Dielectric response and dynamic feature

Yoshihito Hayashi1, Shin Yagihara1

  • 1Department of Physics, Tokai University, Kita-Kaname 4-1-1, Hiratsuka, Kanagawa, 259-1292, Japan.

Biopolymers
|March 29, 2016
PubMed

Immunoglobulin G (IgG) is a Y-shaped globular protein consisting of two Fab segments connecting to an Fc segment with a flexible hinge region, in which the Fab segments show secondary flexibility at an "elbow" region. In the present work, the hinge-bending and elbow-bending motions of aqueous solutions of IgG by microwave dielectric measurements below the freezing point of bulk water was observed. The presence of unfreezable water around the macromolecules reduced the effects of steric hindrance normally generated by ice and enabled the intramolecular motions of IgG. At the same time, the overall IgG molecule rotation was restricted by ice. Papain digestion and reduction of the disulfide linkage at the hinge region was used to generate Fab and Fc fragments. In solutions of these fragments, the dielectric relaxation process of the hinge-bending motion was absent, although the elbow-bending motion remained. Three relaxation processes were observed for papain-digested IgG. The high, middle, and low frequency processes were attributed to unfrozen water, local peptide motions cooperating with bound water, and the elbow-bending motion, respectively. In the case of the intact IgG, an additional relaxation process due to the hinge-bending motion was observed at frequencies lower than that of the elbow-bending motion. © 2016 Wiley Periodicals, Inc. Biopolymers 105: 626-632, 2016.

Related Concept Videos

Mechanisms of Membrane-bending01:15

Mechanisms of Membrane-bending

The living membranes are flexible due to their fluid mosaic nature; however, their bending into different shapes is an active process regulated by specific lipids and proteins. The membrane bending can be transient as seen in vesicles or stable for a long time as in microvilli. Cells regulate the size, location, and duration of the membrane curvature.
Membrane bending can happen due to intrinsic changes in lipid composition or extrinsic association with different proteins. The proteins involved...
3.7K
Antibody Structure01:10

Antibody Structure

Overview
Antibodies, also known as immunoglobulins (Ig), are essential players of the adaptive immune system. These antigen-binding proteins are produced by B cells and make up 20 percent of the total blood plasma by weight. In mammals, antibodies fall into five different classes, which each elicits a different biological response upon antigen binding.
The Y-Shaped Structure of Antibodies Consists of Four Polypeptide Chains
Antibodies consist of four polypeptide chains: two identical heavy...
67.3K
Antibody Structure and Classes01:25

Antibody Structure and Classes

Antibodies, also known as immunoglobulins, are produced by B cells in response to foreign substances, such as bacteria and viruses. These proteins are critical for recognizing and neutralizing these substances, protecting the body from potential harm.
The basic structure of an antibody consists of four protein chains: two identical heavy chains and two identical light chains. These chains are held together by disulfide bonds and other non-covalent interactions, forming a Y-shaped structure.
10.1K
Dielectric Polarization in a Capacitor01:31

Dielectric Polarization in a Capacitor

The presence of a dielectric medium in a capacitor not only changes the voltage and capacitance but also affects the electric field. In general, dielectrics can be of two types: polar and nonpolar. In a polar dielectric, the positive and negative charges in the molecules are separated by a distance and hence have a permanent dipole moment. In contrast, no such charge separation exists in a nonpolar dielectric, however the nonpolar molecules get polarized in the presence of an external electric...
6.4K
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
476