Related Experiment Video

Updated: Mar 16, 2026

Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions
08:18

Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions

Published on: June 12, 2016

17.5K

Slip length measurement of gas flow

Abdelhamid Maali1, Stéphane Colin, Bharat Bhushan

  • 1Univ. Bordeaux, LOMA, UMR 5798, F-33400 Talence, France. CNRS, LOMA, UMR 5798, F-33400 Talence, France.

Nanotechnology
|August 10, 2016
PubMed

More Related Videos

Measurement of Outgassing Rates of Steels08:32

Measurement of Outgassing Rates of Steels

Published on: December 13, 2016

12.1K
Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow08:25

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow

Published on: April 30, 2018

7.7K

Related Concept Videos

Pipe Flowrate Measurement01:28

Pipe Flowrate Measurement

In pipe flow measurement, orifice, nozzle, and Venturi meters are commonly used to determine fluid flowrates by constricting the flow area, which increases fluid velocity and reduces pressure. This pressure difference, governed by Bernoulli's principle and adjusted for real-world conditions, is essential for calculating flowrate. Each meter type is suited to specific applications based on accuracy, efficiency, and compatibility with various flow conditions.
The orifice meter is a simple,...
1.4K
Pipe Flowrate Measurement: Problem Solving01:28

Pipe Flowrate Measurement: Problem Solving

A spray tank system is engineered to uniformly distribute a pest-control liquid across plants by using a pressurized mechanism. The tank, pressurized to 150 kPa, holds the pesticide at a height of 0.80 meters. Liquid flows from the tank through a 1.9 meter pipe with a diameter of 0.015 meters, angled at 0.698 radians, ultimately reaching a 0.007 meter nozzle that sprays the pesticide. Accurate calculation of the system's flow rate is crucial to ensure uniform application, and this is achieved...
948
Laminar Flow: Problem Solving01:24

Laminar Flow: Problem Solving

Laminar flow occurs when a fluid moves smoothly in parallel layers with minimal mixing and turbulence. In fluid mechanics, ensuring laminar flow within a pipe is essential for precise control of flow characteristics, especially in engineering applications. The key factor in determining whether flow remains laminar is the Reynolds number, a dimensionless quantity that depends on the fluid's velocity, density, viscosity, and the pipe's diameter. A Reynolds number of 2100 or lower...
581
Major Losses in Pipes01:28

Major Losses in Pipes

When a fluid flows through a pipe, it experiences energy losses due to frictional resistance along the pipe walls, known as major losses. These energy losses result in a pressure drop, which varies based on the flow conditions — whether laminar or turbulent — and the specific physical properties of the fluid and pipe.
Fluid flow can be classified as laminar or turbulent, primarily based on the Reynolds number. This dimensionless number reflects the relative influence of inertial to viscous...
2.4K
Laminar Flow01:27

Laminar Flow

Laminar flow represents a smooth, orderly fluid motion where particles move along parallel paths, resulting in minimal mixing between layers. Streamlined particle paths characterize this flow regime and occur under conditions where viscous forces dominate over inertial forces. The distinction between laminar, transitional, and turbulent flow is primarily determined by the Reynolds number, a dimensionless quantity calculated as:
2.5K
Design Example: Flow of Oil Through Circular Pipes01:25

Design Example: Flow of Oil Through Circular Pipes

Understanding fluid flow behavior through pipes is critical in fluid mechanics, especially in applications like oil transportation through pipelines. Hagen-Poiseuille's law provides an exact solution derived from the Navier-Stokes equations for steady, incompressible, and laminar flow within a circular pipe. Hagen-Poiseuille's law helps determine the necessary pressure drop across a pipeline section by determining parameters like pipe length, radius, oil viscosity, and the desired volumetric...
530