Related Experiment Video

Updated: Mar 3, 2026

Simultaneously Capturing Real-time Images in Two Emission Channels Using a Dual Camera Emission Splitting System: Applications to Cell Adhesion
10:30

Simultaneously Capturing Real-time Images in Two Emission Channels Using a Dual Camera Emission Splitting System: Applications to Cell Adhesion

Published on: September 4, 2013

10.0K

Joint Source-Channel Coding of JPEG 2000 Image Transmission Over Two-Way Multi-Relay Networks

Chongyuan Bi, Jie Liang

    IEEE Transactions on Image Processing : a Publication of the IEEE Signal Processing Society
    |May 6, 2017
    PubMed

    More Related Videos

    Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping09:43

    Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

    Published on: March 20, 2017

    10.4K
    Quasi-light Storage for Optical Data Packets07:45

    Quasi-light Storage for Optical Data Packets

    Published on: February 6, 2014

    11.4K

    Related Concept Videos

    Differential Relays01:20

    Differential Relays

    Differential relays are used to protect generators, buses, and transformers by comparing electrical quantities at different points. When a fault occurs, the difference in current between the two points triggers the relay to operate, opening the circuit breaker. Under normal conditions, the current entering (i1) and leaving (i2) a generator are equal. When a fault occurs, however, these currents become unequal, and the difference current flows in the relay operating coil, causing the relay to...
    848
    Directional Relays01:25

    Directional Relays

    Directional relays, essential for managing unidirectional fault currents, enhance the safety and efficiency of power systems. On power lines equipped with directional relays, faults downstream (to the right) of the current transformer typically cause the fault current to lag the bus voltage by approximately 90 degrees, known as the forward direction. In contrast, upstream (left-side) faults may result in the fault current leading the bus voltage by nearly 90 degrees, termed the reverse...
    669
    Overcurrent Relays01:26

    Overcurrent Relays

    Overcurrent relays, crucial for circuit protection, are connected to the secondary current of a current transformer. There are two primary types of overcurrent relays: instantaneous and time-delay.
    Instantaneous overcurrent relays activate immediately when the input current exceeds a predetermined value, known as the pickup current, instantly energizing the circuit breaker trip coil. This rapid response is vital for addressing severe faults quickly.
    Time-delay overcurrent relays, on the other...
    611
    Line Protection with Impedance Relays01:27

    Line Protection with Impedance Relays

    Coordinating time-delay overcurrent relays in complex radial systems and directional overcurrent relays in multi-source transmission loops can be challenging. Impedance relays address these issues by responding to the voltage-to-current ratio, specifically measuring the apparent impedance of a line. These relays become more sensitive during faults as current increases and voltage decreases, thereby reducing the apparent impedance.
    Under normal conditions, low load currents keep the measured...
    479
    Pilot and Numeric Relaying01:21

    Pilot and Numeric Relaying

    Pilot relaying is a type of differential protection used in power systems. It compares electrical quantities at the terminals of equipment via a communication channel instead of direct relay interconnection. This method is essential for transmission lines where the terminals are far apart, typically up to 80 km for lines with 69 to 115 kV ratings. Four types of communication channels are used for pilot relaying:
    503
    Network Function of a Circuit01:25

    Network Function of a Circuit

    Frequency response analysis in electrical circuits provides vital insights into a circuit's behavior as the frequency of the input signal changes. The transfer function, a mathematical tool, is instrumental in understanding this behavior. It defines the relationship between phasor output and input and comes in four types: voltage gain, current gain, transfer impedance, and transfer admittance. The critical components of the transfer function are the poles and zeros.
    968