Related Experiment Video

Updated: Feb 8, 2026

Induction of Periodontitis via a Combination of Ligature and Lipopolysaccharide Injection in a Rat Model
06:14

Induction of Periodontitis via a Combination of Ligature and Lipopolysaccharide Injection in a Rat Model

Published on: February 17, 2023

5.2K

Periodontal plastic surgery of gingival recessions at single and multiple teeth

Francesco Cairo

    Periodontology 2000
    |August 1, 2017
    PubMed

    More Related Videos

    Isolation and Culture of Primary Human Gingival Epithelial Cells using Y-2763206:47

    Isolation and Culture of Primary Human Gingival Epithelial Cells using Y-27632

    Published on: November 6, 2021

    5.9K
    Isolation, Processing and Analysis of Murine Gingival Cells09:47

    Isolation, Processing and Analysis of Murine Gingival Cells

    Published on: July 2, 2013

    19.9K

    Related Concept Videos

    Teeth01:15

    Teeth

    The formation of teeth, also known as odontogenesis, is a complex process that begins in utero, around the sixth week of embryonic development. There are three stages to this process: the bud stage, the cap stage, and the bell stage.
    In the bud stage, the tooth germ (an aggregation of cells) starts to form in the developing jawbone. During the cap stage, the tooth germ differentiates into enamel organ, dental papilla, and dental sac, which will later develop into the tooth's enamel, dentin...
    1.8K
    Plastic Deformations of Members with a Single Plane of Symmetry01:21

    Plastic Deformations of Members with a Single Plane of Symmetry

    When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
    375
    Plasticity00:58

    Plasticity

    Plasticity is the property where an object loses its elasticity and undergoes irreversible deformation, even after the deformation forces are eliminated. If a material deforms irreversibly without increasing stress or load, then this is called ideal plasticity. For example, when a force is applied to an aluminum rod, it changes its shape, but it does not return to its original shape once the force is removed. Plastic deformation or ductility is thus a permanent deformation or change in the...
    3.1K
    Plasticizers01:31

    Plasticizers

    Water-reducers, or plasticizers, are chemical admixtures used in concrete to improve strength and workability. These additives reduce the water-cement ratio without compromising workability, lower the cement content while maintaining the same workability, or increase workability to assist concrete placement in inaccessible areas.
    Plasticizers function by using surface-active agents to create repulsive electrostatic forces between cement particles. This dispersion enhances the concrete's...
    374
    Plastic Behavior01:21

    Plastic Behavior

    A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
    580
    Plastic Deformations01:14

    Plastic Deformations

    It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
    471