Related Experiment Video

Updated: Feb 20, 2026

Operation of the Collaborative Composite Manufacturing CCM System
10:09

Operation of the Collaborative Composite Manufacturing CCM System

Published on: October 1, 2019

7.1K

Comparison of tool feed influence in CNC polishing between a novel circular-random path and other pseudo-random paths

Ken Takizawa, Anthony Beaucamp

    Optics Express
    |October 19, 2017
    PubMed

    More Related Videos

    Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats & Spheres13:07

    Convergent Polishing: A Simple, Rapid, Full Aperture Polishing Process of High Quality Optical Flats & Spheres

    Published on: December 1, 2014

    11.7K
    Impact of Fabrication Techniques and Polishing Procedures on Surface Roughness of Denture Base Resins03:02

    Impact of Fabrication Techniques and Polishing Procedures on Surface Roughness of Denture Base Resins

    Published on: January 17, 2025

    1.1K

    Related Concept Videos

    Random Sampling Method01:09

    Random Sampling Method

    Sampling is a technique to select a portion (or subset) of the larger population and study that portion (the sample) to gain information about the population. Data are the result of sampling from a population. The sampling method ensures that samples are drawn without bias and accurately represent the population. Because measuring the entire population in a study is not practical, researchers use samples to represent the population of interest. Among the various sampling methods used by...
    15.1K
    Randomized Experiments01:13

    Randomized Experiments

    The randomization process involves assigning study participants randomly to experimental or control groups based on their probability of being equally assigned. Randomization is meant to eliminate selection bias and balance known and unknown confounding factors so that the control group is similar to the treatment group as much as possible. A computer program and a random number generator can be used to assign participants to groups in a way that minimizes bias.
    Simple randomization
    Simple...
    9.1K
    Circular Shaft - Stresses in Linear Range01:13

    Circular Shaft - Stresses in Linear Range

    Consider a scenario where a circular shaft is subject to torque that remains within the boundaries of Hooke's Law, avoiding any permanent deformation. So, the formula for shearing strain is revisited. This formula is multiplied by the modulus of rigidity, and then Hooke's Law for the shearing stress and strain is applied. As a result, the equation for shearing stress in a shaft can be derived.
    765
    Plastic Deformation in Circular Shafts01:20

    Plastic Deformation in Circular Shafts

    When materials are subjected to forces that surpass their yield strength, they undergo a process known as plastic deformation. This results in a permanent alteration or strain in their structure. This concept can be specifically applied to circular shafts, where the deformation leads to a change in its shape. The precise evaluation of this plastic deformation requires understanding the stress distribution within the circular shaft, which is achieved by calculating the maximum shearing stress in...
    494
    Non-uniform Circular Motion01:22

    Non-uniform Circular Motion

    In uniform circular motion, the particle executing circular motion has a constant speed, and the circle is at a fixed radius. However, not all circular motion occurs at a constant speed. A particle can travel in a circle and speed up or slow down, showing an acceleration in the direction of motion. In that case, the motion is called non-uniform circular motion, and an additional acceleration is introduced, which is in the direction tangential to the circle. 
    For example, such...
    9.8K
    Stress Concentrations in Circular Shafts01:18

    Stress Concentrations in Circular Shafts

    Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
    593