Related Experiment Video

Updated: Feb 19, 2026

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids
11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

9.1K

The underdamped Brownian duet and stochastic linear irreversible thermodynamics

Karel Proesmans1, Christian Van den Broeck1

  • 1Hasselt University, B-3590 Diepenbeek, Belgium.

Chaos (Woodbury, N.Y.)
|November 3, 2017
PubMed

More Related Videos

Analyzing Melts and Fluids from Ab Initio Molecular Dynamics Simulations with the UMD Package06:37

Analyzing Melts and Fluids from Ab Initio Molecular Dynamics Simulations with the UMD Package

Published on: September 17, 2021

5.1K
Cooling an Optically Trapped Ultracold Fermi Gas by Periodical Driving11:21

Cooling an Optically Trapped Ultracold Fermi Gas by Periodical Driving

Published on: March 30, 2017

7.9K

Related Concept Videos

Damped Oscillations01:07

Damped Oscillations

In the real world, oscillations seldom follow true simple harmonic motion. A system that continues its motion indefinitely without losing its amplitude is termed undamped. However, friction of some sort usually dampens the motion, so it fades away or needs more force to continue. For example, a guitar string stops oscillating a few seconds after being plucked. Similarly, one must continually push a swing to keep a child swinging on a playground.
Although friction and other non-conservative...
7.4K
Entropy Change in Reversible Processes01:10

Entropy Change in Reversible Processes

In the Carnot engine, which achieves the maximum efficiency between two reservoirs of fixed temperatures, the total change in entropy is zero. The observation can be generalized by considering any reversible cyclic process consisting of many Carnot cycles. Thus, it can be stated that the total entropy change of any ideal reversible cycle is zero.
The statement can be further generalized to prove that entropy is a state function. Take a cyclic process between any two points on a p-V diagram.
3.3K
Types of Damping01:20

Types of Damping

If the amount of damping in a system is gradually increased, the period and frequency start to become affected because damping opposes, and hence slows, the back and forth motion (the net force is smaller in both directions). If there is a very large amount of damping, the system does not even oscillate; instead, it slowly moves toward equilibrium. In brief, an overdamped system moves slowly towards equilibrium, whereas an underdamped system moves quickly to equilibrium but will oscillate about...
7.8K
Entropy and the Second Law of Thermodynamics01:20

Entropy and the Second Law of Thermodynamics

The second law of thermodynamics can be stated quantitatively using the concept of entropy. Entropy is the measure of disorder of the system.
The relation  between entropy and disorder can be illustrated with the example of the phase change of ice to water. In ice, the molecules are located at specific sites giving a solid state, whereas, in a liquid form, these molecules are much freer to move. The molecular arrangement has therefore become more randomized. Although the change in average...
5.0K
Thermodynamic Systems01:06

Thermodynamic Systems

A thermodynamic system is a set of objects whose thermodynamic properties are of interest. The system is considered to be embedded in its surroundings or the environment. The system and its environment can exchange heat and do work on each other through a boundary that separates them. However, the immediate surroundings of the system interact with it directly and therefore have a much stronger influence on its behavior and properties.
Consider an example of  tea boiling in a kettle. The...
8.7K
Second Order systems II01:18

Second Order systems II

In an underdamped second-order system, where the damping ratio ζ is between 0 and 1, a unit-step input results in a transfer function that, when transformed using the inverse Laplace method, reveals the output response. The output exhibits a damped sinusoidal oscillation, and the difference between the input and output is termed the error signal. This error signal also demonstrates damped oscillatory behavior. Eventually, as the system reaches a steady state, the error diminishes to zero.
427