Related Experiment Video

Updated: Feb 17, 2026

Fabrication and Design of Wood-Based High-Performance Composites
08:08

Fabrication and Design of Wood-Based High-Performance Composites

Published on: November 9, 2019

14.1K

Fabrication and characterization of reversible thermochromic wood veneers

Xiaodong Zhu1, Yu Liu2, Ningwen Dong2

  • 1Key Laboratory of Bio-Based Material Science and Technology (Ministry of Education), Northeast Forestry University, Harbin, Heilongjiang, 150040, China. pse4646@126.com.

Scientific Reports
|December 7, 2017
PubMed

More Related Videos

Towards Biomimicking Wood: Fabricated Free-standing Films of Nanocellulose, Lignin, and a Synthetic Polycation11:26

Towards Biomimicking Wood: Fabricated Free-standing Films of Nanocellulose, Lignin, and a Synthetic Polycation

Published on: June 17, 2014

17.1K
Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material07:42

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

Published on: December 20, 2024

888

Related Concept Videos

Veneer01:19

Veneer

Veneer refers to a thin sheet of wood, typically produced to a thickness of about one-eighth of an inch or less. This material is crafted through various methods, the most common being rotary cutting. In this process, a log is mounted into a large lathe and spun against a knife edge, peeling off a continuous strip of wood as the knife penetrates deeper into the rotating log, creating a rotary-cut veneer.
Other veneering techniques include plain-slicing, quarter-slicing, and rift-slicing. These...
427
Wood Products01:21

Wood Products

Wood products encompass a broad range of materials crafted from wood strands, veneers, lumber, and even waste wood-like shreds, designed for both structural and nonstructural purposes. Various specialized wood products have been developed to enhance strength, durability, and versatility in building applications.
Glue-laminated wood, often referred to as glulam, combines multiple smaller pieces of dimensional lumber using adhesives to form a single, larger piece. Cross-laminated timber consists...
320
Wood Panel Products01:18

Wood Panel Products

Wood panel products are essential materials used in construction for applications such as flooring, siding, and roofing, typically available in standard dimensions of 4 feet by 8 feet, with thicknesses varying from one-quarter of an inch to one and one-eighth inches. Among the most common types of wood panels is plywood, which is produced by gluing multiple layers of thin wood veneers under pressure. The grain of the outer veneers runs lengthwise, while the grains of the interior layers run...
418
Woodward–Hoffmann Selection Rules and Microscopic Reversibility01:34

Woodward–Hoffmann Selection Rules and Microscopic Reversibility

Electrocyclic reactions, cycloadditions, and sigmatropic rearrangements are concerted pericyclic reactions that proceed via a cyclic transition state. These reactions are stereospecific and regioselective. The stereochemistry of the products depends on the symmetry characteristics of the interacting orbitals and the reaction conditions. Accordingly, pericyclic reactions are classified as either symmetry-allowed or symmetry-forbidden. Woodward and Hoffmann presented the selection criteria for...
4.1K
Wood Surfacing01:14

Wood Surfacing

Wood surfacing is a critical finishing process designed to smoothen the wood surface, enhance its dimensional accuracy, and make handling safer. This process compensates for potential shrinkage during the seasoning phase by marginally increasing the wood dimensions before surfacing. It also helps correct some distortions that may occur as the wood dries.
The equipment used in the surfacing process is a plane equipped with rotating blades. This tool efficiently smoothens the wood surface and can...
372
Softwoods and Hardwoods01:28

Softwoods and Hardwoods

Softwoods and hardwoods, derived from different types of trees, are distinguished by their leaf structures and cellular compositions, each serving unique purposes in construction and manufacturing. Softwoods come from cone-bearing trees with needle-like leaves and are predominantly composed of longitudinal cells called tracheids and a smaller proportion of radial cells known as rays. Due to their cellular structure, softwoods are commonly used in construction for structural frames, sheathing,...
605