Related Experiment Video

Updated: Feb 16, 2026

The Frequency Domain Thermoreflectance Technique for Thermal Property Measurements
09:10

The Frequency Domain Thermoreflectance Technique for Thermal Property Measurements

Published on: December 5, 2025

833

Acoustic Properties of Small Animal Soft Tissue in the Frequency Range 12-32 MHz

Adela Rabell-Montiel1, Adrian J Thomson1, Tom A Anderson1

  • 1Centre for Cardiovascular Science, University of Edinburgh, Edinburgh, United Kingdom.

Ultrasound in Medicine & Biology
|December 27, 2017
PubMed

Keywords:
AttenuationBrainHigh frequencyKidneyLiverMiceSpeed of soundUltrasound

More Related Videos

A Probing Device for Quantitatively Measuring the Mechanical Properties of Soft Tissues during Arthroscopy06:16

A Probing Device for Quantitatively Measuring the Mechanical Properties of Soft Tissues during Arthroscopy

Published on: May 1, 2020

5.9K
Microparticle Manipulation by Standing Surface Acoustic Waves with Dual-frequency Excitations06:51

Microparticle Manipulation by Standing Surface Acoustic Waves with Dual-frequency Excitations

Published on: August 21, 2018

7.5K

Related Concept Videos

Variation: Normal Distribution, Range, and Standard Deviation02:32

Variation: Normal Distribution, Range, and Standard Deviation

In the field of psychology, there are several ways to organize measurements of a trait, feature, or characteristic (i.e., variables). Qualitative data, such as ethnicity, can be tabulated into a frequency count to provide information about the proportion, as well as the variety of groups in a sample or population. On the other hand, researchers can perform a wider set of calculations on quantitative data. The mean, mode, and median, for instance, are central tendency measures to identify a...
28.8K
Range00:59

Range

The range is one of the measures of variation. It can be defined as the difference between a dataset's highest and lowest values. For example, in the study of seven 16-ounce soda cans, the filled volume of soda was measured, thus producing the following amount (in ounces) of soda:
15.9; 16.1; 15.2; 14.8; 15.8; 15.9; 16.0; 15.5
Measurements of the amount of soda in a 16-ounce can vary since different subjects record these measurements or since the exact amount - 16 ounces of liquid, was not...
14.5K
Frequency-dependent Selection01:21

Frequency-dependent Selection

When the fitness of a trait is influenced by how common it is (i.e., its frequency) relative to different traits within a population, this is referred to as frequency-dependent selection. Frequency-dependent selection may occur between species or within a single species. This type of selection can either be positive—with more common phenotypes having higher fitness—or negative, with rarer phenotypes conferring increased fitness.
24.2K
Properties of Transition Metals02:58

Properties of Transition Metals

Transition metals are defined as those elements that have partially filled d orbitals. As shown in Figure 1, the d-block elements in groups 3–12 are transition elements. The f-block elements, also called inner transition metals (the lanthanides and actinides), also meet this criterion because the d orbital is partially occupied before the f orbitals.
30.1K
¹H NMR: Long-Range Coupling01:27

¹H NMR: Long-Range Coupling

The coupling interactions of nuclei across four or more bonds are usually weak, with J values less than 1 Hz. While these are usually not observed in spectra, the presence of multiple bonds along the coupling pathway can result in observable long-range coupling.
In alkenes, spin information is communicated via σ–π overlap, as seen in allylic (four-bond) and homoallylic (five-bond) couplings. These coupling interactions are stronger when the σ bond is parallel to the alkene...
2.7K
Angle of Twist - Elastic Range01:13

Angle of Twist - Elastic Range

Consider a cylindrical shaft with a length denoted by L and a consistent cross-sectional radius referred to as r. This shaft undergoes a torque at the free end. The highest shearing strain within the shaft is directly proportional to the twist angle and the radial distance from the shaft axis. When the shaft behaves elastically, this shearing strain can be articulated using variables such as the applied torque, radial distance, the polar moment of inertia, and the modulus of rigidity. By...
844