Related Experiment Video

Updated: Feb 15, 2026

Doxycycline Loaded Collagen-Chitosan Composite Scaffold for the Accelerated Healing of Diabetic Wounds
10:49

Doxycycline Loaded Collagen-Chitosan Composite Scaffold for the Accelerated Healing of Diabetic Wounds

Published on: August 21, 2021

5.0K

Dracorhodin Perchlorate Accelerates Cutaneous Wound Healing in Wistar Rats

Xiao-Wen Jiang1, Lu Qiao1, Lin Liu1

  • 1Department of Veterinary Medicine, Northeast Agricultural University, 59 Mucai Street, Xiangfang District, Harbin 150030, China.

Evidence-Based Complementary and Alternative Medicine : Ecam
|January 16, 2018
PubMed

More Related Videos

Murine Model of Wound Healing05:39

Murine Model of Wound Healing

Published on: May 28, 2013

67.6K
Creation and Transplantation of an Adipose-derived Stem Cell ASC Sheet in a Diabetic Wound-healing Model08:06

Creation and Transplantation of an Adipose-derived Stem Cell ASC Sheet in a Diabetic Wound-healing Model

Published on: August 4, 2017

11.8K

Related Concept Videos

Accelerators01:17

Accelerators

Accelerators in concrete serve as admixtures to speed up the hardening process, enabling the concrete to achieve early strength faster. Although accelerators do not necessarily impact the time it takes concrete to set, they reduce this time in practice. A common accelerator is calcium chloride, which is particularly useful for hastening early strength development in cold weather or for rapid repair jobs that require quick heat generation after mixing.
The effectiveness of calcium chloride can...
294
Average Acceleration01:30

Average Acceleration

The importance of understanding acceleration spans our day-to-day experiences, as well as the vast reaches of outer space and the tiny world of subatomic physics. In everyday conversation, to accelerate means to speed up. For instance, we are familiar with the acceleration of our car; the harder we apply our foot to the gas pedal, the faster we accelerate. The greater the acceleration, the greater the change in velocity over a given time. Acceleration is widely seen in experimental physics. In...
14.6K
Instantaneous Acceleration01:16

Instantaneous Acceleration

Acceleration is in the direction of the change in velocity, but it is not always in the direction of motion. When an object slows down, its acceleration is opposite to the direction of its motion. Although commonly referred to as deceleration, this causes confusion in our analysis as deceleration is not a vector, and does not point to a specific direction with respect to a coordinate system. Therefore, the term deceleration is not used. For example, when a subway train slows down, it...
23.4K
Acceleration Vectors01:30

Acceleration Vectors

In everyday conversation, accelerating means speeding up. Acceleration is a vector in the same direction as the change in velocity, Δv, therefore the greater the acceleration, the greater the change in velocity over a given time. Since velocity is a vector, it can change in magnitude, direction, or both. Thus acceleration is a change in speed or direction, or both. For example, if a runner traveling at 10 km/h due east slows to a stop, reverses direction, and continues their run at 10 km/h...
23.4K
Accelerating Fluids01:17

Accelerating Fluids

When a fluid is in constant acceleration, the pressure and buoyant force equations are modified. Suppose a beaker is placed in an elevator accelerating upward with a constant acceleration, a. In the beaker, assume there is a thin cylinder of height h with an infinitesimal cross-sectional area, ΔS.
The motion of the liquid within this infinitesimal cylinder is considered to obtain the pressure difference. Three vertical forces act on this liquid:
2.3K
Accelerated Curing of Concrete01:25

Accelerated Curing of Concrete

Accelerating concrete curing is achieved by applying heat and additional moisture. This process accelerates the hydration of the cement, resulting in an earlier strength gain in the concrete. Steam curing is a method wherein the concrete products are either transported through a chamber on a conveyor belt or encased in plastic, allowing steam at atmospheric pressure to circulate freely around them. This process begins with a phase of moist curing that typically lasts between 3 to 5 hours, after...
491