Related Experiment Video

Updated: Feb 14, 2026

A Submerged Filter Paper Sandwich for Long-term Ex Ovo Time-lapse Imaging of Early Chick Embryos
07:29

A Submerged Filter Paper Sandwich for Long-term Ex Ovo Time-lapse Imaging of Early Chick Embryos

Published on: December 28, 2016

22.8K

Control of the mixing time in vessels agitated by submerged recirculating jets

Stephen Kennedy1, Pradipto K Bhattacharjee2, Sati N Bhattacharya1

  • 1Chemical and Environmental Engineering, School of Engineering, RMIT University, Melbourne, Victoria 3001, Australia.

Royal Society Open Science
|February 8, 2018
PubMed

Keywords:
ERTjet mixingnon-Newtonian mixingsuction

More Related Videos

Lipid Bilayer Vesicle Generation Using Microfluidic Jetting08:35

Lipid Bilayer Vesicle Generation Using Microfluidic Jetting

Published on: February 21, 2014

15.5K
Permeabilization of Adhered Cells Using an Inert Gas Jet08:21

Permeabilization of Adhered Cells Using an Inert Gas Jet

Published on: September 4, 2013

10.1K

Related Concept Videos

Mixing Time01:19

Mixing Time

The concept of mixing time is significant in producing a uniform concrete mix with the required strength. The mixing period starts once all components are in the mixer. Initially, the mixer is charged with 10% of the water, followed by the consistent addition of solids and then 80% of the water. The remaining water is added later, within the first quarter of the mixing period. The minimum mixing time varies according to the mixer's capacity; for example, mixers with up to 1 cubic yard...
488
Free Jet01:14

Free Jet

Free jets describe the flow of liquid exiting a reservoir through an opening into the atmosphere without resistance. The velocity (v) of the liquid jet is derived using Bernoulli's principle and expressed as:
602
Time-Domain Interpretation of PD Control01:07

Time-Domain Interpretation of PD Control

Proportional-Derivative (PD) control is a widely used control method in various engineering systems to enhance stability and performance. In a system with only proportional control, common issues include high maximum overshoot and oscillation, observed in both the error signal and its rate of change. This behavior can be divided into three distinct phases: initial overshoot, subsequent undershoot, and gradual stabilization.
Consider the example of control of motor torque. Initially, a positive...
408
Buoyancy and Stability for Submerged and Floating Bodies01:11

Buoyancy and Stability for Submerged and Floating Bodies

In fluid mechanics, buoyancy and stability are key concepts for understanding the behavior of submerged and floating bodies. When a stationary body is fully or partially submerged in a fluid, the fluid exerts a force on the body known as the buoyant force. This force acts vertically upward through a point called the center of buoyancy, which is the center of the displaced fluid volume. According to Archimedes' principle, the magnitude of the buoyant force is equal to the weight of the fluid...
2.6K
Time and frequency -Domain Interpretation of PI Control01:27

Time and frequency -Domain Interpretation of PI Control

Proportional-Integral (PI) controllers are essential in many control systems to improve stability and performance. They are commonly used in everyday devices like thermostats to enhance system damping and reduce steady-state error. When the zero in the controller's transfer function is optimally placed, the system benefits significantly in terms of stability and accuracy.
Acting as a low-pass filter, the PI controller slows the system's response and extends settling times. This requires...
441
Time and frequency -Domain Interpretation of Phase-lead Control01:24

Time and frequency -Domain Interpretation of Phase-lead Control

Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
480