Related Experiment Video

Updated: Feb 14, 2026

Genotyping of Staphylococcus aureus by Ribosomal Spacer PCR RS-PCR
08:51

Genotyping of Staphylococcus aureus by Ribosomal Spacer PCR RS-PCR

Published on: November 4, 2016

10.2K

Chronic Osteomyelitis with Staphylococcus aureus Deformation in Submicron Canaliculi of Osteocytes: A Case Report

Karen L de Mesy Bentley1, Ashlee MacDonald, Edward M Schwarz

  • 1Center for Musculoskeletal Research (K.L.d.M.B., A.M., E.M.S., and I.O.) and Departments of Pathology and Laboratory Medicine (K.L.d.M.B. and E.M.S.) and Orthopaedics (K.L.d.M.B., A.M., E.M.S., and I.O.), University of Rochester School of Medicine and Dentistry, Rochester, New York.

JBJS Case Connector
|February 15, 2018
PubMed
Abstract

More Related Videos

Analysis and Imaging of Osteocytes10:19

Analysis and Imaging of Osteocytes

Published on: November 29, 2024

1.3K
Development and Assessment of Intracellular Infection Models for Staphylococcus aureus08:32

Development and Assessment of Intracellular Infection Models for Staphylococcus aureus

Published on: January 17, 2025

1.3K

Related Concept Videos

Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
480
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
485
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
417
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
531
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
497
Deformation in a Circular Shaft01:10

Deformation in a Circular Shaft

One of the distinctive characteristics of circular shafts is their ability to maintain their cross-sectional integrity under torsion. In other words, each cross-section continues to exist as a flat, unaltered entity, simply rotating like a solid, rigid slab. To understand the distribution of shearing stress within such a shaft, consider a cylindrical section inside this circular shaft. This section has a length of L and a radius of R, with one end fixed. The radius of the cylindrical section is...
948