Related Experiment Video

Updated: Feb 13, 2026

Fabrication and Characterization of Disordered Polymer Optical Fibers for Transverse Anderson Localization of Light
09:19

Fabrication and Characterization of Disordered Polymer Optical Fibers for Transverse Anderson Localization of Light

Published on: July 29, 2013

11.9K

Corrigendum: Anderson localization and Mott insulator phase in the time domain

Krzysztof Sacha

    Scientific Reports
    |March 1, 2018
    PubMed
    Summary

    This article provides a correction to the previously published DOI. The correct Digital Object Identifier (DOI) for the article is now available.

    More Related Videos

    Computed Tomography-guided Time-domain Diffuse Fluorescence Tomography in Small Animals for Localization of Cancer Biomarkers12:24

    Computed Tomography-guided Time-domain Diffuse Fluorescence Tomography in Small Animals for Localization of Cancer Biomarkers

    Published on: July 17, 2012

    12.9K
    Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow08:25

    Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow

    Published on: April 30, 2018

    7.7K

    Related Concept Videos

    Time and frequency -Domain Interpretation of Phase-lead Control01:24

    Time and frequency -Domain Interpretation of Phase-lead Control

    Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
    The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
    479
    Time and frequency -Domain Interpretation of Phase-lag Control01:21

    Time and frequency -Domain Interpretation of Phase-lag Control

    Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
    Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any...
    423
    Linear Approximation in Time Domain01:21

    Linear Approximation in Time Domain

    Nonlinear systems often require sophisticated approaches for accurate modeling and analysis, with state-space representation being particularly effective. This method is especially useful for systems where variables and parameters vary with time or operating conditions, such as in a simple pendulum or a translational mechanical system with nonlinear springs.
    For a simple pendulum with a mass evenly distributed along its length and the center of mass located at half the pendulum's length,...
    378
    The Anderson-Darling Test01:16

    The Anderson-Darling Test

    The Anderson-Darling test is a statistical method used to determine whether a data sample is likely drawn from a specific theoretical distribution. Unlike parametric tests, it does not require assumptions about specific parameters of the distribution. Instead, it compares the sample's empirical cumulative distribution function (ECDF) with the cumulative distribution function (CDF) of the hypothesized distribution. Critical values for the test are specific to the chosen distribution rather...
    1.2K
    Time-Domain Interpretation of PD Control01:07

    Time-Domain Interpretation of PD Control

    Proportional-Derivative (PD) control is a widely used control method in various engineering systems to enhance stability and performance. In a system with only proportional control, common issues include high maximum overshoot and oscillation, observed in both the error signal and its rate of change. This behavior can be divided into three distinct phases: initial overshoot, subsequent undershoot, and gradual stabilization.
    Consider the example of control of motor torque. Initially, a positive...
    408
    Conductors and Insulators01:19

    Conductors and Insulators

    Some materials may easily let electrical charges pass through them, while others obstruct their flow. The former are called conductors and the latter insulators. The atomic structures of materials determine whether they are conductors or insulators of electricity.
    Most metals are conductors. Their atomic configuration is such that one or more electron(s) are loosely bound to the nucleus in each atom. Thus, a sea of mobile electrons are available in them, known as free electrons. Their easy...
    10.9K