Related Experiment Video

Updated: Feb 13, 2026

Author Spotlight: Advancing SERS Technology: Au@Carbon Dot Nanoprobes for Label-Free Analysis and Imaging
06:19

Author Spotlight: Advancing SERS Technology: Au@Carbon Dot Nanoprobes for Label-Free Analysis and Imaging

Published on: June 9, 2023

2.1K

Energy Transfer between Semiconducting Polymer Dots and Gold Nanoparticles in a Photoelectrochemical System: A Case

Xiao-Mei Shi1, Li-Ping Mei1, Qian Wang1

  • 1State Key Laboratory of Analytical Chemistry for Life Science and Collaborative Innovation Center of Chemistry for Life Science, School of Chemistry and Chemical Engineering , Nanjing University , Nanjing 210023 , China.

Analytical Chemistry
|March 13, 2018
PubMed

More Related Videos

Gold Nanoparticle Synthesis13:42

Gold Nanoparticle Synthesis

Published on: July 10, 2021

15.9K
Tethered Bilayer Lipid Membranes to Monitor Heat Transfer between Gold Nanoparticles and Lipid Membranes07:33

Tethered Bilayer Lipid Membranes to Monitor Heat Transfer between Gold Nanoparticles and Lipid Membranes

Published on: December 8, 2020

3.1K

Related Concept Videos

Energy Transfer in Chemical Reactions01:16

Energy Transfer in Chemical Reactions

Chemical reactions require sufficient energy to cause the matter to collide with enough precision and force that old chemical bonds can be broken and new ones formed. In general, kinetic energy is the form of energy powering any type of matter in motion. Imagine a person building a brick wall. The energy it takes to lift and place one brick on top of another is the kinetic energy—the energy matter possesses because of its motion. Once the wall is in place, it stores potential energy.
12.3K
Conservation of Energy: Application01:12

Conservation of Energy: Application

When solving problems using the energy conservation law, the object (system) to be studied should first be identified. Often, in applications of energy conservation, we study more than one body at the same time. Second, identify all forces acting on the object and determine whether each force doing work is conservative. If a non-conservative force (e.g., friction) is doing work, then mechanical energy is not conserved. The system must then be analyzed with non-conservative work. Third, for...
8.3K
Application of the Energy Equation01:04

Application of the Energy Equation

The application of the energy equation to centrifugal pumps is a fundamental principle in fluid dynamics and engineering. In this scenario, the energy equation is used to calculate the flow rate of a centrifugal pump responsible for transferring water between two reservoirs at different elevations. The pump applies an energy input of 7500 joules per second, and the vertical difference between the lower and upper reservoirs is 10 meters. Additionally, the head loss due to friction and other...
1.2K
Polymers02:34

Polymers

The word polymer is derived from the Greek words “poly” which means “many” and “mer” which means “parts”. Polymers are long chains of molecules composed of repeating units of smaller molecules, known as monomers. They either occur naturally, such as DNA and proteins, or can be constructed synthetically, like plastics. They have varied structural characteristics, such as linear chains, branched chains, or complex networks, that contribute to the...
41.4K
The Dot Product01:26

The Dot Product

Measuring how one directional quantity affects another along a specific path involves comparing their orientation and strength. When two such quantities are represented using direction and amount, a numerical result is computed to show how much one acts along the path of the other. This result comes from a rule combining both inputs' horizontal and vertical parts and adding the results.This calculation gives a single value that grows larger when both inputs point in similar directions and...
266
Dot Product01:29

Dot Product

The dot product is an essential concept in mathematics and physics.
In engineering, the dot product of any two vectors is the product of the magnitudes of the vectors and the cosine of the angle between them. It is denoted by a dot symbol between the two vectors.
Consider a vehicle pulling an object along the ground using a rope. If the rope makes an angle with the horizontal axis, the work done can be calculated using the dot product of the force applied and the object's displacement.
The dot...
1.0K