Related Experiment Video

Updated: Feb 11, 2026

Contrast-Matching Detergent in Small-Angle Neutron Scattering Experiments for Membrane Protein Structural Analysis and Ab Initio Modeling
10:27

Contrast-Matching Detergent in Small-Angle Neutron Scattering Experiments for Membrane Protein Structural Analysis and Ab Initio Modeling

Published on: October 21, 2018

13.1K

Ab initio effective deformation potentials of phosphorene and consistency checks

Mohammad Elahi1, Mahdi Pourfath1,2

  • 1School of Electrical and Computer Engineering, College of Engineering, University of Tehran, Tehran 14395-515, Iran.

Journal of Physics. Condensed Matter : an Institute of Physics Journal
|April 14, 2018
PubMed
Abstract

More Related Videos

Analyzing Melts and Fluids from Ab Initio Molecular Dynamics Simulations with the UMD Package06:37

Analyzing Melts and Fluids from Ab Initio Molecular Dynamics Simulations with the UMD Package

Published on: September 17, 2021

5.1K
Computation of Atmospheric Concentrations of Molecular Clusters from ab initio Thermochemistry12:11

Computation of Atmospheric Concentrations of Molecular Clusters from ab initio Thermochemistry

Published on: April 8, 2020

8.7K

Related Concept Videos

Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
477
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
477
Protein Folding Quality Check in the RER01:29

Protein Folding Quality Check in the RER

ER is the primary site for the maturation and folding of soluble and transmembrane secretory proteins. The calnexin cycle is a specific chaperone system that folds and assesses the confirmation of N-glycosylated proteins before they can exit the ER lumen. The primary players of this quality check pipeline are the lectins, ER-resident chaperones, and a glucosyl transferase enzyme. In case the calnexin system in the lumen fails to salvage a misfolded protein, it is transported to the cytoplasm...
5.3K
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
415
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
528
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
491