Related Experiment Video

Updated: Feb 11, 2026

Selection of Aptamers for Amyloid β-Protein, the Causative Agent of Alzheimer's Disease
15:23

Selection of Aptamers for Amyloid β-Protein, the Causative Agent of Alzheimer's Disease

Published on: May 13, 2010

19.9K

Development of DNA aptamers targeting low-molecular-weight amyloid-β peptide aggregates in vitro

Madhuri Chakravarthy1, Hadi AlShamaileh, He Huang

  • 1Centre for Comparative Genomics, Murdoch University, Perth, 6150, Australia. R.Veedu@murdoch.edu.au.

Chemical Communications (Cambridge, England)
|April 20, 2018
PubMed

More Related Videos

MR Molecular Imaging of Prostate Cancer with a Small Molecular CLT1 Peptide Targeted Contrast Agent06:54

MR Molecular Imaging of Prostate Cancer with a Small Molecular CLT1 Peptide Targeted Contrast Agent

Published on: September 3, 2013

11.8K
Extraction of High Molecular Weight DNA from Microbial Mats09:30

Extraction of High Molecular Weight DNA from Microbial Mats

Published on: July 7, 2011

20.1K

Related Concept Videos

Amyloid Fibrils03:03

Amyloid Fibrils

Amyloid fibrils are aggregates of misfolded proteins.  Under most circumstances, misfolded proteins are either refolded by chaperone proteins or degraded by the proteasome. However, in the case of a mutation or a disease, these proteins can accumulate to form large clusters and often further assemble to form elongated fibers, called fibrils. 
Amyloid deposits were observed as early as 1639 in the liver and the spleen.   In 1854, Rudolph Virchow performed iodine staining,...
12.0K
Amyloid Fibrils03:03

Amyloid Fibrils

6.5K
Polymers: Defining Molecular Weight01:01

Polymers: Defining Molecular Weight

Unlike small molecules with definite molecular weights, polymers are a mixture of individual polymer chains of varying lengths, each with a unique molecular weight.  So, the molecular weight of a polymer is expressed as an average value based on the average size of the polymer chains. The two most common forms of averages used for polymers are the number average molecular weight and weight average molecular weight.
The number average molecular weight (Mn) is the summation of the number...
3.9K
Polymers: Molecular Weight Distribution01:10

Polymers: Molecular Weight Distribution

For any given polymer, the weight average molecular weight (Mw) is higher than, if not equal to, the number average molecular weight (Mn). The only situation in which the weight average molecular weight and the number average molecular weight are equal is when a polymer consists only of chains with equal molecular weight. However, this never happens in a synthetic polymer, since it is difficult to control the polymerization process up to a molecular level with accuracy to a hundred percent.
4.9K
Molecular Weight of Step-Growth Polymers01:08

Molecular Weight of Step-Growth Polymers

Step growth polymerization involves bi or multifunctional monomers. Bifunctional monomers react to form linear step growth polymers, whereas multifunctional monomers react to form non-linear or branched polymers.
As the step-growth polymerization involves step-wise condensation of monomers, the molecular weight also builds up eventually. Consequently, high molecular weight polymers are obtained at the late stages of the polymerization, where 99% of monomers have been consumed.
The extent of the...
2.9K
Anticoagulant Drugs: Low-Molecular-Weight Heparins01:30

Anticoagulant Drugs: Low-Molecular-Weight Heparins

Hemostasis is a crucial process that prevents excessive blood loss from damaged blood vessels. It involves various mechanisms such as vasoconstriction, platelet adhesion and activation, and fibrin formation. The importance of each mechanism depends on the type of vessel injury. In contrast, thrombosis is the abnormal formation of a blood clot within the blood vessels, leading to potential complications if the clot obstructs blood flow. Thrombosis can be caused by increased coagulability of the...
2.0K