Related Experiment Video

Updated: Feb 11, 2026

Lipid Bilayer Vesicle Generation Using Microfluidic Jetting
08:35

Lipid Bilayer Vesicle Generation Using Microfluidic Jetting

Published on: February 21, 2014

15.5K

Flow Channel Influence of a Collision-Based Piezoelectric Jetting Dispenser on Jet Performance

Can Zhou1,2,3, Guiling Deng4,5, Junhui Li6,7

  • 1School of Mechanical and Electronical Engineering, Central South University, No. 932, South Lushan Road, Changsha 410083, China. zhoucan@csu.edu.cn.

Sensors (Basel, Switzerland)
|April 21, 2018
PubMed

Keywords:
bi-piezoelectric jetflow channel influencemechanical-electrical-fluid simulationmicroelectronics packaging

More Related Videos

Three-dimensional Particle Tracking Velocimetry for Turbulence Applications: Case of a Jet Flow13:02

Three-dimensional Particle Tracking Velocimetry for Turbulence Applications: Case of a Jet Flow

Published on: February 27, 2016

13.0K
Permeabilization of Adhered Cells Using an Inert Gas Jet08:21

Permeabilization of Adhered Cells Using an Inert Gas Jet

Published on: September 4, 2013

10.1K

Related Concept Videos

Free Jet01:14

Free Jet

Free jets describe the flow of liquid exiting a reservoir through an opening into the atmosphere without resistance. The velocity (v) of the liquid jet is derived using Bernoulli's principle and expressed as:
599
Uniform Depth Channel Flow01:27

Uniform Depth Channel Flow

Uniform depth channel flow keeps fluid depth consistent along channels such as irrigation canals. In natural channels, such as rivers, approximate uniform flow is often assumed. This condition occurs when the channel’s bottom slope matches the energy slope, balancing potential energy lost from gravity with head loss due to shear stress. This balance prevents depth changes along the channel length, resulting in a steady, uniform flow.Uniform flow in open channels with a constant cross-section...
612
Energy Considerations in Open Channel Flow01:27

Energy Considerations in Open Channel Flow

Open channel flow, where a fluid flows with a free surface exposed to the atmosphere, is primarily governed by gravitational and surface effects, distinguishing it from closed conduit or pipe flow. In open channels such as rivers, canals, and artificial channels, energy analysis provides valuable insights into flow behavior and the relationship between depth, velocity, and slope.Specific Energy and Flow DepthIn open channel flow, the specific energy, E, combines the gravitational potential...
617
Types Of Collisions - I01:04

Types Of Collisions - I

When two objects come in direct contact with each other, it is called a collision. During a collision, two or more objects exert forces on each other in a relatively short amount of time. A collision can be categorized as either an elastic or inelastic collision. If two or more objects approach each other, collide and then bounce off, moving away from each other with the same relative speed at which they approached each other, the total kinetic energy of the system is said to be conserved. This...
9.5K
Types of Collisions - II01:19

Types of Collisions - II

When two or more objects collide with each other, they can stick together to form one single composite object (after collision). The total mass of the object after the collision is the sum of the masses of the original objects, and it moves with a velocity dictated by the conservation of momentum. Although the system's total momentum remains constant, the kinetic energy decreases, and thus such a collision is an inelastic collision. Most of the collisions between objects in daily life are...
10.0K
Uniform Depth Channel Flow: Problem Solving01:18

Uniform Depth Channel Flow: Problem Solving

To calculate the flow rate for a trapezoidal channel, first, identify the bottom width, side slope, and flow depth of the channel. The cross-sectional area (A) corresponding to the depth of flow (y), channel bottom width (B), and side slope (θ) is determined by:Next, calculate the wetted perimeter, which includes the bottom width and the sloped side lengths in contact with the water. Using the values of the cross-sectional area and the wetted perimeter, determine the hydraulic radius by...
519