Related Experiment Video

Updated: Feb 6, 2026

Extraction and Analysis of Microbial Phospholipid Fatty Acids in Soils
10:03

Extraction and Analysis of Microbial Phospholipid Fatty Acids in Soils

Published on: August 26, 2016

32.4K

Extraction of phospholipids from a dairy by-product (whey protein phospholipid concentrate) using ethanol

Nathan Price1, Tao Fei1, Stephanie Clark2

  • 1Department of Food Science and Human Nutrition, Ames 50011-1061.

Journal of Dairy Science
|August 21, 2018
PubMed

Keywords:
(31)P nuclear magnetic resonancedairy lipidslecithinsphingomyelin

More Related Videos

A Fluorescence-based Assay of Phospholipid Scramblase Activity09:52

A Fluorescence-based Assay of Phospholipid Scramblase Activity

Published on: September 20, 2016

14.7K
Fluorescence Recovery after Merging a Droplet to Measure the Two-dimensional Diffusion of a Phospholipid Monolayer07:54

Fluorescence Recovery after Merging a Droplet to Measure the Two-dimensional Diffusion of a Phospholipid Monolayer

Published on: October 15, 2015

8.5K

Related Concept Videos

Introduction to Membrane Proteins01:16

Introduction to Membrane Proteins

The cell membrane, or plasma membrane, is an ever-changing landscape. It is described as a fluid mosaic where various macromolecules are embedded in the phospholipid bilayer. Among the macromolecules are proteins. The protein content varies across cell types. For example, mitochondrial inner membranes contain ~76% protein content, while myelin contains ~18% protein content. Individual cells contain many types of membrane proteins—red blood cells contain over 50—and different cell...
81.3K
Concentration Cells02:41

Concentration Cells

A concentration cell is a type of a  voltaic cell constructed by connecting two almost identical half-cells, both based on the same half-reaction and using the same electrode, differing only in the concentration of one redox species. A concentration cell's potential, therefore, is determined only by the concentration difference of the particular redox species.
Consider the following voltaic cell:
25.9K
Calculating Equilibrium Concentrations02:05

Calculating Equilibrium Concentrations

Being able to calculate equilibrium concentrations is essential to many areas of science and technology—for example, in the formulation and dosing of pharmaceutical products. After a drug is ingested or injected, it is typically involved in several chemical equilibria that affect its ultimate concentration in the body system of interest. Knowledge of the quantitative aspects of these equilibria is required to compute a dosage amount that will solicit the desired therapeutic effect.
A more...
53.6K
Le Chatelier's Principle: Changing Concentration02:27

Le Chatelier's Principle: Changing Concentration

A system at equilibrium is in a state of dynamic balance, with forward and reverse reactions taking place at equal rates. If an equilibrium system is subjected to a change in conditions that affects these reaction rates differently (a stress), then the rates are no longer equal and the system is not at equilibrium. The system will subsequently experience a net reaction in the direction of a greater rate (a shift) that will re-establish the equilibrium. This phenomenon is summarized by Le...
66.0K
Solution Concentration and Dilution02:59

Solution Concentration and Dilution

The relative amount of a given solution component is known as its concentration. Often, though not always, a solution contains one component with a concentration that is significantly greater than that of all other components. This component is called the solvent and may be viewed as the medium in which the other components are dispersed or dissolved. Solutions in which water is the solvent are, of course, very common on our planet. A solution in which water is the solvent is called an aqueous...
134.7K
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress...
648