Related Experiment Video
Updated: Feb 5, 2026
Building Finite Element Models to Investigate Zebrafish Jaw Biomechanics
Published on: December 3, 2016
Biomechanical behavior of modular acetabular cups made of poly-ether-ether-ketone: A finite element study
Danny Vogel1, Christian Schulze1, Henry Dempwolf1
1Department of Orthopaedics, Biomechanics and Implant Technology Research Laboratory, University of Rostock, Rostock, Germany.
Abstract:
After total hip arthroplasty, stress-shielding is a potential risk factor for aseptic loosening of acetabular cups made of metals. This might be avoided by the use of acetabular cups made of implant materials with lower stiffness. The purpose of this numerical study was to determine whether a modular acetabular cup with a shell made of poly-ether-ether-ketone or poly-ether-ether-ketone reinforced with carbon fibers might be an alternative to conventional metallic shells. Therefore, the press-fit implantation of modular cups with shells made of different materials (Ti6Al4V, poly-ether-ether-ketone, and poly-ether-ether-ketone reinforced with carbon fibers) and varying liner materials (ceramics and ultra-high-molecular-weight polyethylene) into an artificial bone cavity was simulated using finite element analysis. The shell material had a major impact on the radial shell deformation determined at the rim of the shell, ranging from 17.9 µm for titanium over 92.2 µm for poly-ether-ether-ketone reinforced with carbon fibers up to 475.9 µm for poly-ether-ether-ketone. Larger radial liner deformations (up to 618.4 µm) occurred in combination with the shells made of poly-ether-ether-ketone compared to titanium and poly-ether-ether-ketone reinforced with carbon fibers. Hence, it can be stated that conventional poly-ether-ether-ketone is not a suitable shell material for modular acetabular cups. However, the radial shell deformation can be reduced if the poly-ether-ether-ketone reinforced with carbon fiber material is used, while deformation of ceramic liners is similar to the deformation in combination with titanium shells.
More Related Videos
Related Concept Videos
02:29Ethers from Alcohols: Alcohol Dehydration and Williamson Ether Synthesis
Ethers can be prepared from organic compounds by various methods. Some of them are discussed below,
Preparation of Ethers by Alcohol Dehydration
In this method, in the presence of protic acids, alcohol dehydrates to produce alkenes and ethers under different conditions. For example, in the presence of sulphuric acid, dehydration of ethanol at 413 K yields ethoxyethane, whereas it yields ethene at 443 K.
02:36Crown Ethers
02:28Structure and Nomenclature of Ethers
Ethers are organic compounds with an ether functional group which is characterized by an oxygen atom connected to two — identical or different — alkyl, aryl, or vinyl groups. The C–O–C linkage in dimethyl ether — the simplest ether — has an approximately tetrahedral bond angle of 110.3 degrees. The oxygen atom is sp3- hybridized, with the C–O distance being about 140 pm.
Classification of Ethers
Based on their attached substituent...
02:17Physical Properties of Ethers
An ether molecule has a net dipole moment due to the polarity of C–O bonds. Subsequently, boiling points of ethers are lower than those of alcohols of comparable molecular weight and slightly higher than those of hydrocarbons of comparable molecular weight (Table 1).
Ethers can act as hydrogen bond acceptors, making them more water-soluble than hydrocarbons, but since ethers cannot act as hydrogen bond donors, they are much less soluble in water than alcohols. Ethers are considered...
02:23Autoxidation of Ethers to Peroxides and Hydroperoxides
02:18Ethers to Alkyl Halides: Acidic Cleavage