Related Experiment Video

Updated: Feb 5, 2026

Site-Directed Immobilization of Bone Morphogenetic Protein 2 to Solid Surfaces by Click Chemistry
11:20

Site-Directed Immobilization of Bone Morphogenetic Protein 2 to Solid Surfaces by Click Chemistry

Published on: March 29, 2018

8.0K

Design of Modular Polyhydroxyalkanoate Scaffolds for Protein Immobilization by Directed Ligation

Jin Xiang Wong1,2, Bernd H A Rehm3

  • 1Institute of Fundamental Sciences , Massey University , Private Bag , 11222 Palmerston North , New Zealand.

Biomacromolecules
|September 11, 2018
PubMed

More Related Videos

Covalent Immobilization of Proteins for the Single Molecule Force Spectroscopy11:13

Covalent Immobilization of Proteins for the Single Molecule Force Spectroscopy

Published on: August 20, 2018

11.6K
The Modular Design and Production of an Intelligent Robot Based on a Closed-Loop Control Strategy11:53

The Modular Design and Production of an Intelligent Robot Based on a Closed-Loop Control Strategy

Published on: October 14, 2017

12.2K

Related Concept Videos

Directing Proteins to the Rough Endoplasmic Reticulum01:34

Directing Proteins to the Rough Endoplasmic Reticulum

The organelle-specific signaling sequences direct proteins synthesized in the cytosol to their final destination like ER, mitochondria, peroxisomes, etc. Some of the proteins directed to ER are then trafficked via vesicles to other organelles within the cell or the extracellular environment through the Golgi complex. For example, the rough ER synthesizes soluble proteins for transportation to the lysosomes or secretion out of the cell. It can also synthesize transmembrane proteins that can...
17.8K
Group Design02:01

Group Design

The most basic experimental design involves two groups: the experimental group and the control group. The two groups are designed to be the same except for one difference— experimental manipulation. The experimental group gets the experimental manipulation—that is, the treatment or variable being tested—and the control group does not. Since experimental manipulation is the only difference between the experimental and control groups, we can be sure that any differences between...
10.6K
Factorial Design02:01

Factorial Design

Factorial Analysis is an experimental design that applies Analysis of Variance (ANOVA) statistical procedures to examine a change in a dependent variable due to more than one independent variable, also known as factors. Changes in worker productivity can be reasoned, for example, to be influenced by salary and other conditions, such as skill level. One way to test this hypothesis is by categorizing salary into three levels (low, moderate, and high) and skills sets into two levels (entry level...
13.8K
Design Example: Designing a Residential Plumbing System01:25

Design Example: Designing a Residential Plumbing System

The design of residential plumbing systems requires carefully evaluating water demand, flow rates, and pressure dynamics to ensure both efficiency and reliability. The nature of water flow within pipes is defined by its Reynolds number, which classifies flow as either laminar (smooth) or turbulent.
1.1K
Design Example: Designing Water Slide01:18

Design Example: Designing Water Slide

When designing a water slide, controlling the speed of water flow is crucial for rider safety while maintaining an exciting experience. As water flows down the slide, gravity causes it to accelerate, with its speed at the bottom depending on the height from which it starts. The higher the slide, the more potential energy the water has at the top, which is converted into kinetic energy as it descends, increasing its speed.
Bernoulli's principle determines the water's velocity along the slide....
630
Design Example: Design of an Irrigation Channel01:27

Design Example: Design of an Irrigation Channel

Trapezoidal channels are widely used in irrigation systems due to their cost-effectiveness and efficiency in conveying water. Trapezoidal channels feature a flat bottom and sloping sides, making them stable and easier to construct compared to other shapes. The bottom width and side slope ratio are determined based on the required flow capacity and site conditions. The side slope is kept gentle for unlined channels to prevent soil erosion.Hydraulic parameters in channel design include the flow...
843