Related Experiment Video

Updated: Feb 5, 2026

A Novel Arthroscopic Medial Knot-Tying Suture-Bridge Repair with Rip-Stop Technique for Rotator Cuff Tears
06:41

A Novel Arthroscopic Medial Knot-Tying Suture-Bridge Repair with Rip-Stop Technique for Rotator Cuff Tears

Published on: January 13, 2026

156

[Arthroscopic-assisted stabilization of medial shoulder instability in a Miniature Poodle]

A Penelas1, A Pozzi1, E Stańczyk2

  • 1Klinik für Kleintierchirurgie, Vetsuisse-Fakultät, Universität Zürich.

Schweizer Archiv Fur Tierheilkunde
|September 13, 2018
PubMed
Abstract

Keywords:
Arthroscopic stabilizationArthroskopische StabilisierungGlenohumerales BandHundKnochenankerSchultergelenks­instabilitätSubskapularissehnebone anchordoggleno-humeral ligamentinstability of the shoulder jointsubscapularis tendon

More Related Videos

Reverse Total Shoulder Arthroplasty10:10

Reverse Total Shoulder Arthroplasty

Published on: July 5, 2011

44.0K
Autologous Microfractured and Purified Adipose Tissue for Arthroscopic Management of Osteochondral Lesions of the Talus07:24

Autologous Microfractured and Purified Adipose Tissue for Arthroscopic Management of Osteochondral Lesions of the Talus

Published on: January 23, 2018

10.8K

Related Concept Videos

Muscles of the Shoulder01:23

Muscles of the Shoulder

The muscles surrounding the shoulder girdle, including the clavicle and scapula, primarily stabilize the scapula. This stable base allows other muscles to move the humerus effectively. Scapular movements often mirror those of the humerus and extend its range of motion. For instance, raising the arm above the head would not be feasible without simultaneous upward rotation of the scapula.
Anterior Thoracic Muscles
The anterior thoracic muscles include the serratus anterior, subclavius, and...
9.2K
Microtubule Instability02:17

Microtubule Instability

Microtubules are hollow cylindrical filaments having a diameter of approximately 25 nm and a length that varies from 200 nm to 25 μm. GTP-bound tubulin subunits form αβ-heterodimers for microtubule assembly. These core building blocks interact longitudinally, polymerizing into protofilaments. The protofilaments then interact with one another through lateral bonding forces to form stable cylindrical microtubules. These cylindrical filaments are dynamic as they undergo repeated...
6.3K
Nuclear Stability03:18

Nuclear Stability

Protons and neutrons, collectively called nucleons, are packed together tightly in a nucleus. With a radius of about 10−15 meters, a nucleus is quite small compared to the radius of the entire atom, which is about 10−10 meters. Nuclei are extremely dense compared to bulk matter, averaging 1.8 × 1014 grams per cubic centimeter. If the earth’s density were equal to the average nuclear density, the earth’s radius would be only about 200 meters.
To hold positively charged protons together...
23.3K
RNA Stability01:53

RNA Stability

Intact DNA strands can be found in fossils, while scientists sometimes struggle to keep RNA intact under laboratory conditions. The structural variations between RNA and DNA underlie the differences in their stability and longevity. Because DNA is double-stranded, it is inherently more stable. The single-stranded structure of RNA is less stable but also more flexible and can form weak internal bonds. Additionally, most RNAs in the cell are relatively short, while DNA can be up to 250 million...
35.7K
Stability01:28

Stability

The time response of a linear time-invariant (LTI) system can be divided into transient and steady-state responses. The transient response represents the system's initial reaction to a change in input and diminishes to zero over time. In contrast, the steady-state response is the behavior that persists after the transient effects have faded.
The stability of an LTI system is determined by the roots of its characteristic equation, known as poles. A system is stable if it produces a bounded...
419
Stability of structures01:14

Stability of structures

In mechanical engineering, the stability of systems under various forces is critical for designing durable and efficient structures. One fundamental way to explore these concepts is by analyzing systems like two rods connected at a pivot point, O, with a torsional spring of spring constant k at the pivot point. This system is similar in appearance to a scissor jack used to change tires on a car. In this case, the arms of the linkage (equivalent to the rods in this system) are entirely vertical,...
531