Related Experiment Video

Updated: Feb 5, 2026

Application of a Coupling Agent to Improve the Dielectric Properties of Polymer-Based Nanocomposites
06:34

Application of a Coupling Agent to Improve the Dielectric Properties of Polymer-Based Nanocomposites

Published on: September 19, 2020

6.4K

Accelerated Curing and Enhanced Material Properties of Conductive Polymer Nanocomposites by Joule Heating

Sung-Hwan Jang1, Donghak Kim2, Yong-Lae Park3,4,5

  • 1Civil and Coastal Engineering, School of Engineering, University of Plymouth, Plymouth, Devon PL4 8AA, UK. sung-hwan.jang@plymouth.ac.uk.

Materials (Basel, Switzerland)
|September 22, 2018
PubMed

Keywords:
Joule heatingcarbon nanotubesconductive polymersparticulate composites

More Related Videos

Concurrent Quantitative Conductivity and Mechanical Properties Measurements of Organic Photovoltaic Materials using AFM08:59

Concurrent Quantitative Conductivity and Mechanical Properties Measurements of Organic Photovoltaic Materials using AFM

Published on: January 23, 2013

12.2K
Electroactive Polymer Nanoparticles Exhibiting Photothermal Properties10:16

Electroactive Polymer Nanoparticles Exhibiting Photothermal Properties

Published on: January 8, 2016

14.3K

Related Concept Videos

Accelerated Curing of Concrete01:25

Accelerated Curing of Concrete

Accelerating concrete curing is achieved by applying heat and additional moisture. This process accelerates the hydration of the cement, resulting in an earlier strength gain in the concrete. Steam curing is a method wherein the concrete products are either transported through a chamber on a conveyor belt or encased in plastic, allowing steam at atmospheric pressure to circulate freely around them. This process begins with a phase of moist curing that typically lasts between 3 to 5 hours, after...
481
Quantifying Heat02:46

Quantifying Heat

Thermal Energy Microscopically, thermal energy is the kinetic energy associated with the random motion of atoms and molecules. Temperature is a quantitative measure of “hot” or “cold”, which depends on the amount of thermal energy. When the atoms and molecules in an object are moving or vibrating quickly, they have a higher average kinetic energy (KE) (or higher thermal energy), and the object is perceived as “hot”, or it is described as being at a higher temperature. When the...
62.2K
Joule-Thomson Effect01:21

Joule-Thomson Effect

The Joule-Thomson effect, also known as the Joule-Kelvin effect, describes the temperature change of a fluid when it is forced through a valve or porous plug while keeping it in a thermally insulated environment. This experiment is called a throttling process. This is an important effect widely used in refrigeration and the liquefaction of gases.
This experiment forces high-pressure gas through a throttle valve or a porous plug to a lower-pressure region. The gas expands as it passes through to...
9.7K
Polymers02:34

Polymers

The word polymer is derived from the Greek words “poly” which means “many” and “mer” which means “parts”. Polymers are long chains of molecules composed of repeating units of smaller molecules, known as monomers. They either occur naturally, such as DNA and proteins, or can be constructed synthetically, like plastics. They have varied structural characteristics, such as linear chains, branched chains, or complex networks, that contribute to the...
40.9K
Curing of Concrete01:20

Curing of Concrete

The hydration of cement takes place within the water-filled capillary pores. However, environmental elements can disrupt this process by evaporating water from the concrete surfaces. Sealed concrete with a water-cement ratio below 0.5 experiences self-desiccation, leading to water loss. The water loss in concrete is mitigated by curing. This technique involves keeping the concrete saturated to maintain the necessary temperature and moisture conditions, to optimally fill the spaces in the cement...
369
Curing Methods01:26

Curing Methods

Concrete members with a small surface-to-volume ratio are cured by oiling and moistening the forms before casting the concrete member. These forms can be left in place for a prolonged period to prevent moisture loss, and can be wetted if made of a material suitable for wetting. If the forms are removed early, the concrete member is moistened and covered with polythene sheets to maintain moisture. For large horizontal concrete surfaces exposed to dry weather, a temporary covering is suspended...
303