Related Experiment Video

Updated: Feb 3, 2026

Advanced Experimental Methods for Low-temperature Magnetotransport Measurement of Novel Materials
10:36

Advanced Experimental Methods for Low-temperature Magnetotransport Measurement of Novel Materials

Published on: January 21, 2016

11.3K

Standard Reference Materials for Cement Paste: Part III-Analysis of the Flow Characteristics for the Developed

Dong Kyu Lee1, Myoung Sung Choi2

  • 1Department of Safety Engineering, College of Engineering, Dongguk University-Gyeongju, 123 Dongdae-ro, Gyeongju 38066, Korea. dklee@dongguk.ac.kr.

Materials (Basel, Switzerland)
|October 19, 2018
PubMed

Keywords:
plastic viscosityrheologystandard reference materialstemperatureyield stress

More Related Videos

Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy07:44

Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy

Published on: April 27, 2016

10.1K
Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material07:42

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

Published on: December 20, 2024

855

Related Concept Videos

Standard Entropy Change for a Reaction03:00

Standard Entropy Change for a Reaction

Entropy is a state function, so the standard entropy change for a chemical reaction (ΔS°rxn) can be calculated from the difference in standard entropy between the products and the reactants.
24.6K
Porosity in Cement Paste01:18

Porosity in Cement Paste

The porosity of concrete is a measure of the void spaces within its structure. These spaces impact its strength and durability significantly. When water and cement interact, a chemical reaction called hydration creates a semi-solid paste. This paste includes combined water, making up approximately 23% of the cement's dry mass, and gel water, which fills minuscule voids known as gel pores, accounting for about 28% of the cement gel volume.
The balance of water to cement in the mix is...
464
Standard Enthalpy of Formation02:37

Standard Enthalpy of Formation

Enthalpy changes are typically tabulated for reactions in which both the reactants and products are at the same conditions. A standard state is a commonly accepted set of conditions used as a reference point for the determination of properties under other different conditions. For chemists, the IUPAC standard state refers to materials under a pressure of 1 bar and solutions at 1 M and does not specify a temperature. Many thermochemical tables list values with a standard state of 1 atm. Because...
49.2K
Inertial Frames of Reference01:03

Inertial Frames of Reference

Newton’s first law is usually considered to be a statement about reference frames. It provides a method for identifying a special type of reference frame: the inertial reference frame. In principle, we can make the net force on a body zero. If its velocity relative to a given frame is constant, then that frame is said to be inertial. So, by definition, an inertial reference frame is a reference frame where Newton's first law holds valid. Newton's first law applies to objects with...
8.8K
Non-inertial Frames of Reference01:27

Non-inertial Frames of Reference

A reference frame accelerating or decelerating relative to an inertial frame is a non-inertial frame. To help understand this, consider what taking off in an airplane, turning a corner in a car, riding a merry-go-round, and the circular motion of a tropical cyclone all have in common. All these systems are accelerating, decelerating, or rotating relative to the Earth; hence, they all are non-inertial frames. All these systems exhibit inertial forces, which merely seem to arise from motion,...
7.2K
Calculating Standard Free Energy Changes02:49

Calculating Standard Free Energy Changes

The free energy change for a reaction that occurs under the standard conditions of 1 bar pressure and at 298 K is called the standard free energy change. Since free energy is a state function, its value depends only on the conditions of the initial and final states of the system. A convenient and common approach to the calculation of free energy changes for physical and chemical reactions is by use of widely available compilations of standard state thermodynamic data. One method involves the...
24.9K