Related Experiment Video

Updated: Feb 3, 2026

Motor Dual-Tasks for Gait Analysis and Evaluation in Post-Stroke Patients
05:23

Motor Dual-Tasks for Gait Analysis and Evaluation in Post-Stroke Patients

Published on: March 11, 2021

2.9K

Effect of task specific circuit training on Gait parameters and mobility in stroke survivors

Qurat-Ul-Ain1, Arshad Nawaz Malik2, Umama Haq3

  • 1Dr. Qurat-ul-Ain, MSNMPT, Department of Physical Therapy, Pakistan Railway Hospital, Riphah International University, Islamabad, Pakistan.

Pakistan Journal of Medical Sciences
|October 23, 2018
PubMed

Keywords:
Circuit gait trainingGait ParametersStrokeTimed get up and go

More Related Videos

The Impact of Motor Task Conditions on Goal-Directed Arm Reaching Kinematics and Trunk Compensation in Chronic Stroke Survivors15:00

The Impact of Motor Task Conditions on Goal-Directed Arm Reaching Kinematics and Trunk Compensation in Chronic Stroke Survivors

Published on: May 2, 2021

4.1K
A Rehabilitation Program of Exoskeleton-assisted Body Weight-Supported Treadmill Training with Non-immersive Virtual Reality for Stroke Patients06:00

A Rehabilitation Program of Exoskeleton-assisted Body Weight-Supported Treadmill Training with Non-immersive Virtual Reality for Stroke Patients

Published on: May 16, 2025

1.2K

Related Concept Videos

Wave Parameters01:10

Wave Parameters

The simplest mechanical waves are associated with simple harmonic motion and repeat themselves for several cycles. These simple harmonic waves can be modeled using a combination of sine and cosine functions. Consider a simplified surface water wave that moves across the water's surface. Unlike complex ocean waves, in surface water waves, water moves vertically, oscillating up and down, whereas the disturbance of the wave moves horizontally through the medium. If a seagull is floating on the...
9.3K
Second-Order Circuits01:17

Second-Order Circuits

Integrating two fundamental energy storage elements in electrical circuits results in second-order circuits, encompassing RLC circuits and circuits with dual capacitors or inductors (RC and RL circuits). Second-order circuits are identified by second-order differential equations that link input and output signals.
Input signals typically originate from voltage or current sources, with the output often representing voltage across the capacitor and/or current through the inductor. For example, in...
3.6K
First-Order Circuits01:15

First-Order Circuits

First-order electrical circuits, which comprise resistors and a single energy storage element - either a capacitor or an inductor, are fundamental to many electronic systems. These circuits are governed by a first-order differential equation that describes the relationship between input and output signals.
One common example of a first-order circuit is the RC (resistor-capacitor) circuit. These circuits are used in relaxation oscillators such as neon lamp oscillator circuits. When voltage is...
3.8K
The Y-to-Y Circuit01:19

The Y-to-Y Circuit

In a balanced four-wire wye-to-wye system, the arrangement involves wye-connected sinusoidal voltage sources and loads, connected through a neutral wire that links the neutral nodes of the source and load. The load impedance is connected across each phase of the load. The wye-connected source can be connected to the wye-connected load in four-wire and three-wire arrangements. A three-phase system is considered balanced when the load on each phase is equal, leading to uniform current flow and...
755
LC Circuits01:21

LC Circuits

An LC circuit consists of an inductor and a capacitor, either in series or parallel. Consider a charged capacitor connected with an inductor in series. Before the switch is closed, all the energy of the circuit is stored in the electric field of the capacitor. When the switch is closed, the capacitor begins to discharge, producing a current in the circuit. The current, in turn, creates a magnetic field in the inductor. Because of the induced emf in the inductor, the current cannot change...
3.3K
Three-Phase Circuits01:22

Three-Phase Circuits

AC power distribution systems have three categories: single-phase, two-phase, and three-phase systems. The single-phase circuit, common in residential settings, typically employs a two-wire system connecting a single AC source to various loads. These circuits support standard household appliances operating at 120 volts (V) and 240 V, such as lamps, televisions, and microwaves. The first generators, Niagara Falls hydro plant installed in 1895, were two-phase and designed by Nikola Tesla. The...
834