Related Experiment Video

Updated: Feb 2, 2026

Quantitative Hardness Measurement by Instrumented AFM-indentation
08:21

Quantitative Hardness Measurement by Instrumented AFM-indentation

Published on: November 22, 2016

10.2K

Localized Deformation and Fracture Behaviors in InP Single Crystals by Indentation

Yi-Jui Chiu1, Sheng-Rui Jian2, Ti-Ju Liu3

  • 1School of Mechanical and Automotive Engineering, Xiamen University of Technology, No.600 Ligong Road, Jimei District, Xiamen 361024, China. chiuyijui@xmut.edu.cn.

Micromachines
|November 25, 2018
PubMed

Keywords:
InP(100) single crystalPop-infracture toughnessnanoindentationtransmission electron microscopy

More Related Videos

Comparison of Two Different Synthesis Methods of Single Crystals of Superconducting Uranium Ditelluride04:51

Comparison of Two Different Synthesis Methods of Single Crystals of Superconducting Uranium Ditelluride

Published on: July 8, 2021

3.2K
High Pressure Single Crystal Diffraction at PX^211:32

High Pressure Single Crystal Diffraction at PX^2

Published on: January 16, 2017

22.1K

Related Concept Videos

Plastic Deformations of Members with a Single Plane of Symmetry01:21

Plastic Deformations of Members with a Single Plane of Symmetry

When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
371
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
466
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
444
Ionic Crystal Structures02:42

Ionic Crystal Structures

Ionic crystals consist of two or more different kinds of ions that usually have different sizes. The packing of these ions into a crystal structure is more complex than the packing of metal atoms that are the same size.
Most monatomic ions behave as charged spheres, and their attraction for ions of opposite charge is the same in every direction. Consequently, stable structures for ionic compounds result (1) when ions of one charge are surrounded by as many ions as possible of the opposite...
17.0K
Crystal Growth: Principles of Crystallization01:25

Crystal Growth: Principles of Crystallization

Crystallization is a phase transformation process in which crystals are precipitated from a supersaturated solution or formed from other sources. During crystallization, atoms or molecules arrange themselves into a well-defined, rigid crystal lattice to minimize energy.
Initiating crystallization involves manipulating the concentration of the solute and the temperature of the solution. Since crystal growth occurs when the ratio of concentration and solubility of the solute in the solvent...
5.0K
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
399