Related Experiment Video

Updated: Feb 2, 2026

Writing Bragg Gratings in Multicore Fibers
08:48

Writing Bragg Gratings in Multicore Fibers

Published on: April 20, 2016

8.7K

Design and fabrication of multiplexed volume Bragg gratings as angle amplifiers in high power beam scanning system

Peng Chen, Yunxia Jin, Dongbing He

    Optics Express
    |November 25, 2018
    PubMed

    More Related Videos

    A Random-displacement Measurement by Combining a Magnetic Scale and Two Fiber Bragg Gratings08:23

    A Random-displacement Measurement by Combining a Magnetic Scale and Two Fiber Bragg Gratings

    Published on: September 30, 2019

    6.7K
    Measurement of X-ray Beam Coherence along Multiple Directions Using 2-D Checkerboard Phase Grating10:39

    Measurement of X-ray Beam Coherence along Multiple Directions Using 2-D Checkerboard Phase Grating

    Published on: October 11, 2016

    10.1K

    Related Concept Videos

    Design Example: Traverse Angle Computations01:25

    Design Example: Traverse Angle Computations

    Traverse angle computations are a critical component of surveying, used to compute the internal angles within a closed traverse. A traverse consists of a series of connected lines forming a closed loop, often used for land boundary delineation or mapping. Calculating the internal angles ensures accuracy in the traverse geometry and is essential for checking survey data integrity.The process begins with known azimuths and bearings of the traverse sides. Internal angles at each vertex are...
    341
    Design of Prismatic Beams for Bending01:23

    Design of Prismatic Beams for Bending

    The design of prismatic beams, structural elements with a uniform cross-section, focuses on ensuring safety and structural integrity under load. The design process begins by determining the allowable stress, either from material properties tables, or by dividing the material's ultimate strength by a safety factor. This safety factor is essential for accommodating uncertainties, and varies depending on the material—timber, steel, or concrete—with each having unique strength and...
    631
    Operational Amplifiers01:17

    Operational Amplifiers

    The operational amplifier, often referred to as an op-amp, is a multifaceted building block of a circuit. This electronic component functions like a voltage-controlled voltage source and can also be used to create a voltage- or current-controlled current source. The design of an operational amplifier enables it to execute mathematical operations when external components like resistors and capacitors are linked to its terminals. An op-amp has the capacity to sum signals, amplify a signal,...
    2.0K
    MOSFET Amplifiers01:17

    MOSFET Amplifiers

    The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
    523
    BJT Amplifiers01:14

    BJT Amplifiers

    Bipolar Junction Transistors (BJTs) are pivotal components in amplifier circuits, functioning as voltage-controlled current sources in their active region. This characteristic allows them to efficiently control the collector current through variations in the base-emitter voltage. Essentially, BJTs amplify power due to their ability to take a weak input signal and output a much stronger signal.
    In BJT amplifier configurations, particularly in common-emitter setups, the transistor's role...
    984
    Beams01:30

    Beams

    Beams are integral components of structural engineering and construction, designed to support loads applied at various points along their length. These long, straight members can be classified based on geometry, cross-section, support type, and equilibrium condition.
    Based on geometry, beams can be straight, tapered, or curved. Straight beams are the most common type and have a constant cross-section throughout their length. Tapered beams, on the other hand, have a varying cross-section along...
    1.9K