Related Experiment Video

Updated: Feb 2, 2026

Author Spotlight: Quantitative Characterization of Liquid Photosensitive Bioink Properties for Continuous Digital Light Processing Based Printing
04:32

Author Spotlight: Quantitative Characterization of Liquid Photosensitive Bioink Properties for Continuous Digital Light Processing Based Printing

Published on: April 14, 2023

1.7K

Evaluation of Cure Depth and Geometrical Overgrowth Depending on Zirconia Volume Fraction Using Digital Light

Kyoung-Jun Jang1, Jin-Ho Kang1, Kumaresan Sakthiabirami1

  • 1Department of Prosthodontics, School of Dentistry, Chonnam National University, Gwangju 500-757, Korea.

Journal of Nanoscience and Nanotechnology
|November 30, 2018
PubMed

More Related Videos

One-Step Approach to Fabricating Polydimethylsiloxane Microfluidic Channels of Different Geometric Sections by Sequential Wet Etching Processes08:31

One-Step Approach to Fabricating Polydimethylsiloxane Microfluidic Channels of Different Geometric Sections by Sequential Wet Etching Processes

Published on: September 13, 2018

10.4K
Digital Microfluidics for Automated Proteomic Processing10:55

Digital Microfluidics for Automated Proteomic Processing

Published on: November 6, 2009

13.0K

Related Concept Videos

Geometric Mean01:15

Geometric Mean

The mean is a measure of the central tendency of a data set. In some data sets, the data is inherently multiplicative, and the arithmetic mean is not useful. For example, the human population multiplies with time, and so does the credit amount of financial investment, as the interest compounds over successive time intervals.
In cases of multiplicative data, the geometric mean is used for statistical analysis. First, the product of all the elements is taken. Then, if there are n elements in the...
4.0K
Pressure and Volume in an Adiabatic Process01:27

Pressure and Volume in an Adiabatic Process

Free expansion of a gas is an adiabatic process. However, there are few differences between free expansion and adiabatic expansion. During free expansion, no work is done, and there is no change in internal energy. But, for an adiabatic expansion, work is done, and there is a change in internal energy. During an adiabatic process, the relation between the pressure and volume is obtained from the condition for the adiabatic process, that is,
3.5K
Geometric Sequences01:30

Geometric Sequences

In systems where values diminish by a constant proportion at each stage, the resulting sequence follows a geometric structure. Each new value in the sequence is obtained by applying a fixed multiplier to the preceding term. This regular, proportional decline type is often used to represent processes involving gradual loss, such as energy dissipation or reduction in amplitude over time.When analyzing the total effect of such a process across unlimited iterations, the series of values is referred...
288
Curing of Concrete01:20

Curing of Concrete

The hydration of cement takes place within the water-filled capillary pores. However, environmental elements can disrupt this process by evaporating water from the concrete surfaces. Sealed concrete with a water-cement ratio below 0.5 experiences self-desiccation, leading to water loss. The water loss in concrete is mitigated by curing. This technique involves keeping the concrete saturated to maintain the necessary temperature and moisture conditions, to optimally fill the spaces in the cement...
370
Curing Methods01:26

Curing Methods

Concrete members with a small surface-to-volume ratio are cured by oiling and moistening the forms before casting the concrete member. These forms can be left in place for a prolonged period to prevent moisture loss, and can be wetted if made of a material suitable for wetting. If the forms are removed early, the concrete member is moistened and covered with polythene sheets to maintain moisture. For large horizontal concrete surfaces exposed to dry weather, a temporary covering is suspended...
299
Accelerated Curing of Concrete01:25

Accelerated Curing of Concrete

Accelerating concrete curing is achieved by applying heat and additional moisture. This process accelerates the hydration of the cement, resulting in an earlier strength gain in the concrete. Steam curing is a method wherein the concrete products are either transported through a chamber on a conveyor belt or encased in plastic, allowing steam at atmospheric pressure to circulate freely around them. This process begins with a phase of moist curing that typically lasts between 3 to 5 hours, after...
483