Related Experiment Video

Updated: Jan 31, 2026

Determining Tribocorrosion Rate and Wear-Corrosion Synergy of Bulk and Thin Film Aluminum Alloys
07:12

Determining Tribocorrosion Rate and Wear-Corrosion Synergy of Bulk and Thin Film Aluminum Alloys

Published on: September 11, 2018

11.9K

Preparation of Textured Surfaces on Aluminum-Alloy Substrates

Markéta Kadlečková1,2, Antonín Minařík3,4, Petr Smolka5,6

  • 1Department of Physics and Materials Engineering, Faculty of Technology, Tomas Bata University in Zlín, Vavrečkova 275, 760 01 Zlín, Czech Republic. m1_kadleckova@utb.cz.

Materials (Basel, Switzerland)
|January 4, 2019
PubMed

Keywords:
adhesive bondingalloyaluminumduraluminetchingporous-likesuperhydrophobicsurface texture

More Related Videos

An Available Technique for Preparation of New Cast MnCuNiFeZnAl Alloy with Superior Damping Capacity and High Service Temperature14:51

An Available Technique for Preparation of New Cast MnCuNiFeZnAl Alloy with Superior Damping Capacity and High Service Temperature

Published on: September 23, 2018

7.4K
Hydrogen Charging of Aluminum using Friction in Water07:50

Hydrogen Charging of Aluminum using Friction in Water

Published on: January 28, 2020

6.5K

Related Concept Videos

Shape and Texture of Coarse Aggregate01:25

Shape and Texture of Coarse Aggregate

Aggregate shape is classified based on the relative sharpness or roundness of the edges and corners. This classification includes categories like rounded, angular, elongated, and flaky, each with specific characteristics. Rounded aggregates, fully shaped by attrition, are typical of river or seashore gravel, while angular aggregates, such as crushed rock, have well-defined edges. Aggregates that are elongated and flaky are less desirable, as they can reduce the workability and strength of...
682
Surface Tension and Surface Energy01:16

Surface Tension and Surface Energy

When a paint brush is immersed in water, the bristles wave freely inside the water. When it is taken out, the bristles stick together. The reason behind this effect is surface tension.
Consider a beaker filled with liquid. The bulk molecules in the liquid experience equal attractive forces on all sides with the surrounding molecules. However, the surface molecules experience a net attractive force downward due to the bulk molecules. The surface of the liquid behaves like a stretched membrane,...
3.2K
Wood Surfacing01:14

Wood Surfacing

Wood surfacing is a critical finishing process designed to smoothen the wood surface, enhance its dimensional accuracy, and make handling safer. This process compensates for potential shrinkage during the seasoning phase by marginally increasing the wood dimensions before surfacing. It also helps correct some distortions that may occur as the wood dries.
The equipment used in the surfacing process is a plane equipped with rotating blades. This tool efficiently smoothens the wood surface and can...
353
Cell-surface Signaling01:21

Cell-surface Signaling

Hormones—or any molecule that binds to a receptor, known as a ligand—that are lipid-insoluble (water-soluble) are not able to diffuse across the cell membrane. In order to be able to affect a cell without entering it, these hormones bind to receptors on the cell membrane. When a first messenger, a hormone, binds to a receptor, a signal cascade is set off, causing second messengers, proteins inside the cell, to become activated, resulting in downstream effects.
54.4K
Area of a Surface of Revolution01:29

Area of a Surface of Revolution

Surfaces of revolution are formed when a two-dimensional curve is rotated around an axis, producing a three-dimensional shape. This concept is used in engineering tasks like determining the surface area of a rocket nozzle, where precise calculations are critical for applying uniform heat-resistant coatings. When a curve is revolved about the x-axis, it sweeps out a continuous surface whose area must be calculated accurately to estimate material requirements.Approximating with Conical BandsTo...
54
Equipotential Surfaces and Conductors01:16

Equipotential Surfaces and Conductors

For a conductor in which all charges are at rest, the conductor's surface is equipotential. The electric field is always perpendicular to equipotential surfaces. Therefore, in a conductor with static charges, the electric field just outside the conductor is always perpendicular to the conductor's surface. Any tangential component of the electric field will cause charges to move inside the conductor, which will violate the electrostatic nature of the system. In an electrostatic...
4.4K