Related Experiment Video

Updated: Jan 30, 2026

Less-Invasive Technique for Non-stabilized Mandibular Fracture in Mouse Models
04:13

Less-Invasive Technique for Non-stabilized Mandibular Fracture in Mouse Models

Published on: September 27, 2024

876

Unusual Horizontal Root Fracture in a Mandibular Second Molar after Lower Wisdom Teeth Removal

Luiz Fernando Magacho Da Silva1, Jonathan Ribeiro Da Silva1, Fabrizio Albieri1

  • 1Department of Oral and Maxillofacial Surgery, General Hospital of Nova Iguaçu, Rio de Janeiro, Brazil.

Annals of Maxillofacial Surgery
|January 30, 2019
PubMed

Keywords:
Dental traumahorizontal root fracturewisdom teeth

More Related Videos

The Establishment of a Murine Mandibular Molar Extraction Socket Healing Model04:19

The Establishment of a Murine Mandibular Molar Extraction Socket Healing Model

Published on: January 13, 2023

5.6K
3D Imaging of PDL Collagen Fibers during Orthodontic Tooth Movement in Mandibular Murine Model09:33

3D Imaging of PDL Collagen Fibers during Orthodontic Tooth Movement in Mandibular Murine Model

Published on: April 15, 2021

5.6K

Related Concept Videos

Molar Mass01:54

Molar Mass

The identity of a substance is defined not only by the types of atoms or ions it contains but by the quantity of each type of atom or ion. For example, water, H2O, and hydrogen peroxide, H2O2, are alike in that their respective molecules are composed of hydrogen and oxygen atoms. However, because a hydrogen peroxide molecule contains two oxygen atoms, as opposed to the water molecule, which has only one, the two substances exhibit very different properties.
86.6K
Unusual Results01:16

Unusual Results

Unusual results are those that have a very low chance of occurring. Unusual results can be identified using probabilities and the range rule of thumb. In problems involving probability, unusual results can be observed in 2 instances – an unusually high number of successes or an unusually low number of successes.
According to the range rule of thumb, any value above or below two standard deviations, 2σ  from the mean, μ  is considered unusual.
Maximum unusual value =...
3.8K
Teeth01:15

Teeth

The formation of teeth, also known as odontogenesis, is a complex process that begins in utero, around the sixth week of embryonic development. There are three stages to this process: the bud stage, the cap stage, and the bell stage.
In the bud stage, the tooth germ (an aggregation of cells) starts to form in the developing jawbone. During the cap stage, the tooth germ differentiates into enamel organ, dental papilla, and dental sac, which will later develop into the tooth's enamel, dentin...
1.8K
z Scores and Unusual Values01:07

z Scores and Unusual Values

The z score is one of the three measures of relative standing. It describes the location of a value in a dataset relative to the mean. z scores are obtained after the standardization of the values in a dataset. The z score for the mean is 0.
 This score indicates how far a value is from the mean in terms of standard deviation. For example, if a data value has a z score of +1, the researcher can infer that the particular data value is one standard deviation above the mean. If another data...
11.0K
Introduction to Horizontal Curves01:19

Introduction to Horizontal Curves

Horizontal curves are essential in highway and railroad design, ensuring smooth and safe transitions between straight path segments, or tangents. These curves allow vehicles to maintain speed without abrupt changes, minimizing accidents and improving travel efficiency.A horizontal curve is typically defined by its geometric relationship to two tangents that meet at an intersection point (P.I.), where a simple curve is introduced to connect them. The back tangent refers to the initial tangent...
674
Horizontal Curve: Problem Solving01:03

Horizontal Curve: Problem Solving

A horizontal curve is characterized by its radius, intersection angle, and stationing of key points. In this case, the radius is 400 meters, and the angle of intersection is 30 degrees, with the station of the point of curvature (P.C.) at 0 + 150 meters. The goal is to determine the station values at the point of intersection (P.I.), point of tangency (P.T.), and midpoint of the curve, as well as the length of the long chord.The process begins with calculating the tangent distance (T) and the...
376