Related Experiment Video

Updated: Jan 30, 2026

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material
07:42

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

Published on: December 20, 2024

851

Restoration of a Mandibular Incisor With a Computer-aided Design/Computer-aided Manufacturing Fabricated Anterior

J May, J Watson

    Operative Dentistry
    |February 1, 2019
    PubMed

    More Related Videos

    Hydra, a Computer-Based Platform for Aiding Clinicians in Cardiovascular Analysis and Diagnosis07:51

    Hydra, a Computer-Based Platform for Aiding Clinicians in Cardiovascular Analysis and Diagnosis

    Published on: September 26, 2018

    8.1K
    Detection and Removal of Tooth-Colored Composite Resin Using the Fluorescence-Aided Identification Technique05:42

    Detection and Removal of Tooth-Colored Composite Resin Using the Fluorescence-Aided Identification Technique

    Published on: July 27, 2022

    4.4K

    Related Concept Videos

    Restorative Care01:19

    Restorative Care

    Restorative care is provided once a patient has been discharged from a healthcare facility and requires additional services. The additional services include home care, rehabilitation programs, and extended care. Restorative care centers help the patient regain their previous level of functioning or acquire a new level of functioning due to the incapacitating effects of a disease or a disability. It aims to assist patients in enhancing their quality of life by encouraging independence,...
    2.4K
    Steel Manufacturing01:26

    Steel Manufacturing

    Steel manufacturing is a multi-stage process that begins by smelting iron ore into cast iron in a blast furnace. This initial stage involves layering iron ore with coke, a type of fuel, and crushed limestone within the furnace. The coke is ignited with a high volume of air, leading to the creation of carbon monoxide, which acts to reduce the iron ore to pure iron.
    During this smelting process, limestone plays a crucial role by forming slag. Slag captures impurities within the molten iron, such...
    1.5K
    Group Design02:01

    Group Design

    The most basic experimental design involves two groups: the experimental group and the control group. The two groups are designed to be the same except for one difference— experimental manipulation. The experimental group gets the experimental manipulation—that is, the treatment or variable being tested—and the control group does not. Since experimental manipulation is the only difference between the experimental and control groups, we can be sure that any differences between...
    10.4K
    Muscles of the Anterior Neck01:26

    Muscles of the Anterior Neck

    The anterior neck muscles are the group of muscles covering the front part of the neck. These muscles are classified into three subgroups. The first one is the superficial muscles, the most visible muscles in the front of the neck. It includes the platysma and sternocleidomastoid. The second group is the suprahyoid muscles, located above the hyoid bone. This group comprises the digastric, mylohyoid, geniohyoid, and stylohyoid. Lastly, the infrahyoid muscles are found below the hyoid bone and...
    4.7K
    Factorial Design02:01

    Factorial Design

    Factorial Analysis is an experimental design that applies Analysis of Variance (ANOVA) statistical procedures to examine a change in a dependent variable due to more than one independent variable, also known as factors. Changes in worker productivity can be reasoned, for example, to be influenced by salary and other conditions, such as skill level. One way to test this hypothesis is by categorizing salary into three levels (low, moderate, and high) and skills sets into two levels (entry level...
    13.8K
    Manufacture of Concrete Masonry Units01:27

    Manufacture of Concrete Masonry Units

    The process of manufacturing concrete masonry units begins by mixing stiff concrete composed of Portland cement, aggregates, and water. This mixture is then poured into metal molds. To ensure the concrete settles uniformly and to avoid separation of its components, the mixture in the molds is subjected to vibration. Shortly after, the still-wet blocks are removed from the molds and placed on racks.
    These wet blocks are then transported for curing, which can occur in one of two environments: a...
    405