Related Experiment Video

Updated: Jan 28, 2026

Lumican Extraction from Amniotic Membrane and Determination of its Storage Temperature
04:21

Lumican Extraction from Amniotic Membrane and Determination of its Storage Temperature

Published on: October 14, 2022

1.8K

Effects of High-Temperature Storage on the Elasticity Modulus of an Epoxy Molding Compound

Ruifeng Li1,2, Daoguo Yang3,4, Ping Zhang5

  • 1School of Automation, Beijing University of Posts and Telecommunications, No.10 Xitucheng Road, Beijing 100876, China. liruifeng8107@163.com.

Materials (Basel, Switzerland)
|March 3, 2019
PubMed

Keywords:
elasticity modulusepoxy molding compoundhigh-temperature storagemicroelectronics reliability

More Related Videos

An Externally-Heated Diamond Anvil Cell for Synthesis and Single-Crystal Elasticity Determination of Ice-VII at High Pressure-Temperature Conditions07:48

An Externally-Heated Diamond Anvil Cell for Synthesis and Single-Crystal Elasticity Determination of Ice-VII at High Pressure-Temperature Conditions

Published on: June 18, 2020

7.4K
Evaluation of the Storage Stability of Extracellular Vesicles11:31

Evaluation of the Storage Stability of Extracellular Vesicles

Published on: May 22, 2019

15.0K

Related Concept Videos

Strain and Elastic Modulus01:15

Strain and Elastic Modulus

The quantity that describes the deformation of a body under stress is known as strain. Strain is given as a fractional change in either length, volume, or geometry under tensile, volume (also known as bulk), or shear stress, respectively, and is a dimensionless quantity. The strain experienced by a body under tensile or compressive stress is called tensile or compressive strain, respectively. In contrast, the strain experienced under bulk stress and shear stress is known as volume and shear...
9.1K
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
586
Dynamic Modulus of Elasticity of Concrete01:16

Dynamic Modulus of Elasticity of Concrete

The dynamic modulus of elasticity assesses how a concrete structure deforms under impact or dynamic loads. It is typically higher than the static modulus of elasticity, measured under slow, steady loading conditions.
The sonic test is a common method to determine the dynamic modulus. In this test, a concrete beam, sized either 6 x 6 x 30 inches or 4 x 4 x 20 inches, is clamped at its center. Vibrations are initiated at one end of the beam by an electromagnetic exciter unit powered by a...
993
Effects of Temperature on Free Energy02:11

Effects of Temperature on Free Energy

The spontaneity of a process depends upon the temperature of the system. Phase transitions, for example, will proceed spontaneously in one direction or the other depending upon the temperature of the substance in question. Likewise, some chemical reactions can also exhibit temperature-dependent spontaneities. To illustrate this concept, the equation relating free energy change to the enthalpy and entropy changes for the process is considered:
28.2K
Atomic Spectroscopy: Effects of Temperature01:27

Atomic Spectroscopy: Effects of Temperature

Atomization, converting samples into gas-phase atoms and ions, is essential for atomic spectroscopy. The flame temperature required for atomization affects the efficiency of the atomic spectroscopic methods by increasing the atomization efficiency and the relative population of the excited and ground states.
At thermal equilibrium, the relative populations of excited and ground state atoms can be estimated using the Maxwell–Boltzmann distribution. For example, an increase in temperature...
898
Bulk Modulus01:21

Bulk Modulus

The bulk modulus is a scientific term used to describe a material's resistance to uniform compression. It is the proportionality constant that links a change in pressure to the resulting relative volume change.
754