Related Experiment Video

Updated: Jan 27, 2026

An Available Technique for Preparation of New Cast MnCuNiFeZnAl Alloy with Superior Damping Capacity and High Service Temperature
14:51

An Available Technique for Preparation of New Cast MnCuNiFeZnAl Alloy with Superior Damping Capacity and High Service Temperature

Published on: September 23, 2018

7.4K

Effect of Heat Treatment on the Compressive Behavior of Zinc Alloy ZA27 Syntactic Foam

Nima Movahedi1, Graeme E Murch2, Irina V Belova3

  • 1Centre for Mass and Thermal Transport in Engineering Materials, School of Engineering, The University of Newcastle, Callaghan, NSW 2308, Australia. nima.movahedi@uon.edu.au.

Materials (Basel, Switzerland)
|March 15, 2019
PubMed

Keywords:
brittle and ductile deformationexpanded perliteheat treatmentmetallic syntactic foamzinc alloy

More Related Videos

Zinc-Sponge Battery Electrodes that Suppress Dendrites06:58

Zinc-Sponge Battery Electrodes that Suppress Dendrites

Published on: September 29, 2020

4.8K
Author Spotlight: Exploring Cellular Zinc Regulation Through ZnT1 Functionality07:55

Author Spotlight: Exploring Cellular Zinc Regulation Through ZnT1 Functionality

Published on: June 2, 2023

1.6K

Related Concept Videos

Behavior of Concrete Under Compressive Load01:23

Behavior of Concrete Under Compressive Load

Concrete exhibits specific behaviors under different compressive loads. Understanding this is crucial for understanding its structural integrity. When concrete undergoes uniaxial compression, it tends to develop cracks that run parallel to the direction of the force. These parallel cracks stem from localized tensile stresses that occur perpendicular to the compression direction. Additionally, angled cracks may appear due to the formation of shear planes.
As the concrete specimen fractures under...
618
Heating and Cooling Curves02:44

Heating and Cooling Curves

When a substance—isolated from its environment—is subjected to heat changes, corresponding changes in temperature and phase of the substance is observed; this is graphically represented by heating and cooling curves.
For instance, the addition of heat raises the temperature of a solid; the amount of heat absorbed depends on the heat capacity of the solid (q = mcsolidΔT). According to thermochemistry, the relation between the amount of heat absorbed or released by a substance, q, and its...
27.6K
Quantifying Heat02:46

Quantifying Heat

Thermal Energy Microscopically, thermal energy is the kinetic energy associated with the random motion of atoms and molecules. Temperature is a quantitative measure of “hot” or “cold”, which depends on the amount of thermal energy. When the atoms and molecules in an object are moving or vibrating quickly, they have a higher average kinetic energy (KE) (or higher thermal energy), and the object is perceived as “hot”, or it is described as being at a higher temperature. When the...
62.0K
Specific Heat01:16

Specific Heat

The specific heat capacity of a substance refers to the energy required to increase the temperature of one gram of that substance by one degree Celcius. Specific heat capacity is often represented in calories (cal), grams (g), and degrees Celsius (oC), but can also be expressed in joules (J), kilograms (kg), and Kelvin (K), among other units.
For example, increasing the temperature of one gram of water by 1°C requires one calorie of heat energy and can be written as 1 cal/g-°C, or...
67.4K
Heat Flow and Specific Heat01:12

Heat Flow and Specific Heat

Heat is a type of energy transfer that is caused by a temperature difference, and it can change the temperature of an object. Since heat is a form of energy, its SI unit is the joule (J). Another common unit of energy often used for heat is the calorie (cal), which is defined as the energy needed to change the temperature of 1 g of water by 1 °C, specifically between 14.5 °C and 15.5 °C, since the energy needed shows a slight temperature dependence. Another commonly used unit is...
6.8K
Heat and Free Expansion01:24

Heat and Free Expansion

The work done by a thermodynamic system depends not only on the initial and final states but also on the intermediate states—that is, on the path. Like work, when heat is added to a thermodynamic system, it undergoes a change of state, and the state attained depends on the path from the initial state to the final state. Consider an ideal gas cylinder fitted with a piston. When the cylinder is heated at a constant temperature, the gas molecules absorb energy and expand slowly in a...
2.9K