Related Experiment Video

Updated: Jan 25, 2026

Chip-based Three-dimensional Cell Culture in Perfused Micro-bioreactors
12:39

Chip-based Three-dimensional Cell Culture in Perfused Micro-bioreactors

Published on: May 21, 2008

12.0K

On-chip magnetic-free optical multi-port circulator based on a locally linear parity-time symmetric system

Fakhroddin Nazari, Shahab Abdollahi, Farid Samsami-Khodadad

    Applied Optics
    |May 3, 2019
    PubMed

    More Related Videos

    Microfluidic Chip for Axonal Injury Models Construction and Enabling Multi-Omics Analysis11:00

    Microfluidic Chip for Axonal Injury Models Construction and Enabling Multi-Omics Analysis

    Published on: October 14, 2025

    1.2K
    Lensfree On-chip Tomographic Microscopy Employing Multi-angle Illumination and Pixel Super-resolution08:41

    Lensfree On-chip Tomographic Microscopy Employing Multi-angle Illumination and Pixel Super-resolution

    Published on: August 16, 2012

    12.0K

    Related Concept Videos

    Linear time-invariant Systems01:23

    Linear time-invariant Systems

    A system is linear if it displays the characteristics of homogeneity and additivity, together termed the superposition property. This principle is fundamental in all linear systems. Linear time-invariant (LTI) systems include systems with linear elements and constant parameters.
    The input-output behavior of an LTI system can be fully defined by its response to an impulsive excitation at its input. Once this impulse response is known, the system's reaction to any other input can be...
    893
    Linear Approximation in Time Domain01:21

    Linear Approximation in Time Domain

    Nonlinear systems often require sophisticated approaches for accurate modeling and analysis, with state-space representation being particularly effective. This method is especially useful for systems where variables and parameters vary with time or operating conditions, such as in a simple pendulum or a translational mechanical system with nonlinear springs.
    For a simple pendulum with a mass evenly distributed along its length and the center of mass located at half the pendulum's length,...
    360
    Voltammetric Techniques: Linear-Scan (E vs Time)01:12

    Voltammetric Techniques: Linear-Scan (E vs Time)

    Polarography is a classical voltammetric technique used to analyze electrochemical reactions. This method applies a linear potential sweep to a dropping mercury electrode (DME), and the resulting current is measured. A dropping mercury electrode is commonly used as the working electrode in polarography. It consists of a capillary tube filled with mercury, where the tiny droplet forms at the tip. This droplet continuously drops from the capillary, creating a new electrode surface for each...
    1.1K
    Symmetric Member in Bending01:07

    Symmetric Member in Bending

    In the study of the mechanics of materials, analyzing the behavior of prismatic members under opposing couples is crucial for understanding internal stress distributions, which are essential for structural design. When subjected to couples, a prismatic member experiences internal forces that maintain equilibrium. A couple, characterized by two equal and opposite forces, creates a moment but no resultant force. The internal forces at any section cut of the member must balance these external...
    574
    Deformations in a Symmetric Member in Bending01:18

    Deformations in a Symmetric Member in Bending

    When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
    When the member is segmented into tiny cubic elements, it is observed that the primary stress...
    485
    Beams with Symmetric Loadings01:15

    Beams with Symmetric Loadings

    The moment-area method is an analytical tool used in structural engineering to determine the slope and deflection of beams under various loads. Consider a cantilever with a concentrated load and moment at the free end. The first step is constructing a free-body diagram to calculate the reactions at the fixed end. Next, the bending moment diagram is plotted to visualize how the bending moment varies along the beam's length, focusing on points where the bending moment equals zero.
    The M/EI...
    391