Related Experiment Video
Updated: Jan 25, 2026
Author Spotlight: Three-Dimensional Cephalometric Landmark Annotation Demonstration on Human Cone Beam Computed Tomography Scans
Published on: September 8, 2023
Adaptation of Single-Cone Gutta-Percha in Curved Canals Prepared and Obturated with Protaper and Heroshaper Systems
Yuvika Ahluwalia1, Utsav Sharma2, Neeraj Kumar3
1Reader, Institute of Dental Sciences and Technologies, Kadrabad, Modinagar Uttar Pardesh, Ghaziabad, India.
Objective:
The aim of this study is to prepare and obturate the curved canals of the mesiobuccal root of maxillary first molar with four different file systems that is protaper hand files, rotary pro taper (RP) files, heroshaper hand files, and rotary hero shapers files and to evaluate the adaptation of their single-cone Gutta-percha by cone beam computed tomography (CBCT).
Materials And Methods:
Eighty teeth were selected and were divided into two groups (G1A1, G1A2 and G2A1, G2A2 as hand and RP file system, G1A3, G1A4 and G2A3, G2A4 as hand and rotary hero shaper files system) of fourth teeth each. After access opening working length of the mesiobuccal canal was established. The distobuccal and palatal roots of the samples were removed using the diamond disc at the furcation level. "Endoanalyser" software was used to measure Schneider's angle on the preoperative radiograph. This angle was measured by drawing two lines-one parallel to the long axis of the canal, in the coronal third, and the second line from the apical foramen to intersect the point where the first line left the long axis of the canal. The canals of each group were then prepared according to the manufacturer's instructions for protaper hand files, RP files, heroshaper hand files, and rotary hero shapers files systems. Direct digital radiography image of all the samples was obtained. And then, the samples were exposed to CBCT to evaluate their single-cone adaptations. The data were analyzed using SPSS 20, IBM, Armonk, NY, United States of America.
Results:
The null hypothesis that there will not be any gap area in the adaptation of their single-cone of different file system was rejected. Minimal gap area was seen in rotary hero shapers file system (0.001 mm2) and was maximum in hand protaper (HP) file system (0.015 mm2).
Conclusion:
CBCT is a useful tool in detecting the gap area after obturation in curved canals. The HP single-cone adaptation showed the maximum gap area and rotary heroshaper single-cone adaptation showed the minimum gap area.
More Related Videos
Related Concept Videos
01:10Computed Tomography
The technique was invented in the 1970s and is based on the principle that as X-rays pass through the body, they are absorbed or reflected at different levels. In the technique, a patient lies on a motorized platform while a computerized axial tomography (CAT) scanner rotates...
01:27Imaging Studies III: Computed Tomography
01:24Single Pipe Systems
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
01:30Beams
Based on geometry, beams can be straight, tapered, or curved. Straight beams are the most common type and have a constant cross-section throughout their length. Tapered beams, on the other hand, have a varying cross-section along...
01:07Electron Microscope Tomography and Single-particle Reconstruction
Electron Tomography
Electron tomography can be performed either in TEM or STEM (scanning transmission...
02:44Heating and Cooling Curves
For instance, the addition of heat raises the temperature of a solid; the amount of heat absorbed depends on the heat capacity of the solid (q = mcsolidΔT). According to thermochemistry, the relation between the amount of heat absorbed or released by a substance, q, and its...