Related Experiment Video

Updated: Jan 24, 2026

High Temperature Fabrication of Nanostructured Yttria-Stabilized-Zirconia YSZ Scaffolds by In Situ Carbon Templating Xerogels
07:13

High Temperature Fabrication of Nanostructured Yttria-Stabilized-Zirconia YSZ Scaffolds by In Situ Carbon Templating Xerogels

Published on: April 16, 2017

11.2K

Nanocellulose Xerogels With High Porosities and Large Specific Surface Areas

Shunsuke Yamasaki1, Wataru Sakuma1, Hiroaki Yasui1

  • 1Department of Biomaterial Sciences, Graduate School of Agricultural and Life Sciences, The University of Tokyo, Tokyo, Japan.

Frontiers in Chemistry
|May 29, 2019
PubMed

Keywords:
aerogelambient pressure dryingcellulose nanofiberporous materialxerogel

More Related Videos

Towards Biomimicking Wood: Fabricated Free-standing Films of Nanocellulose, Lignin, and a Synthetic Polycation11:26

Towards Biomimicking Wood: Fabricated Free-standing Films of Nanocellulose, Lignin, and a Synthetic Polycation

Published on: June 17, 2014

17.0K
Fabrication of a Functionalized Magnetic Bacterial Nanocellulose with Iron Oxide Nanoparticles08:59

Fabrication of a Functionalized Magnetic Bacterial Nanocellulose with Iron Oxide Nanoparticles

Published on: May 26, 2016

13.8K

Related Concept Videos

Porosity and Absorption of Aggregate01:20

Porosity and Absorption of Aggregate

Aggregates contain pores of varying sizes; while some are completely enclosed within the particles, others open onto the surface, allowing water to penetrate. The porosity of aggregates is a major factor contributing to the overall porosity of concrete, given that aggregates constitute about three-quarters of concrete's volume.
When all pores in an aggregate are filled with water, the aggregate is considered saturated and surface-dry. If left in dry air, water will evaporate until the...
772
Porosity in Cement Paste01:18

Porosity in Cement Paste

The porosity of concrete is a measure of the void spaces within its structure. These spaces impact its strength and durability significantly. When water and cement interact, a chemical reaction called hydration creates a semi-solid paste. This paste includes combined water, making up approximately 23% of the cement's dry mass, and gel water, which fills minuscule voids known as gel pores, accounting for about 28% of the cement gel volume.
The balance of water to cement in the mix is...
454
Surface Tension and Surface Energy01:16

Surface Tension and Surface Energy

When a paint brush is immersed in water, the bristles wave freely inside the water. When it is taken out, the bristles stick together. The reason behind this effect is surface tension.
Consider a beaker filled with liquid. The bulk molecules in the liquid experience equal attractive forces on all sides with the surrounding molecules. However, the surface molecules experience a net attractive force downward due to the bulk molecules. The surface of the liquid behaves like a stretched membrane,...
3.2K
Specific Heat01:16

Specific Heat

The specific heat capacity of a substance refers to the energy required to increase the temperature of one gram of that substance by one degree Celcius. Specific heat capacity is often represented in calories (cal), grams (g), and degrees Celsius (oC), but can also be expressed in joules (J), kilograms (kg), and Kelvin (K), among other units.
For example, increasing the temperature of one gram of water by 1°C requires one calorie of heat energy and can be written as 1 cal/g-°C, or...
67.3K
Wood Surfacing01:14

Wood Surfacing

Wood surfacing is a critical finishing process designed to smoothen the wood surface, enhance its dimensional accuracy, and make handling safer. This process compensates for potential shrinkage during the seasoning phase by marginally increasing the wood dimensions before surfacing. It also helps correct some distortions that may occur as the wood dries.
The equipment used in the surfacing process is a plane equipped with rotating blades. This tool efficiently smoothens the wood surface and can...
351
Cell-surface Signaling01:21

Cell-surface Signaling

Hormones—or any molecule that binds to a receptor, known as a ligand—that are lipid-insoluble (water-soluble) are not able to diffuse across the cell membrane. In order to be able to affect a cell without entering it, these hormones bind to receptors on the cell membrane. When a first messenger, a hormone, binds to a receptor, a signal cascade is set off, causing second messengers, proteins inside the cell, to become activated, resulting in downstream effects.
54.0K