Related Experiment Video

Updated: Jan 24, 2026

Author Spotlight: Development of a Novel Finite Element Analysis Model for Improved Orthognathic Surgical Techniques
07:16

Author Spotlight: Development of a Novel Finite Element Analysis Model for Improved Orthognathic Surgical Techniques

Published on: October 20, 2023

1.8K

Glue embolisation of a bleeding pseudoaneurysm related to surgically-assisted rapid palatal expansion

O Maleux1, O da Costa Senior1, C Politis1

  • 1Department of Oral and Maxillofacial Surgery, University Hospitals Leuven, Herestraat 49, 3000, Leuven, Belgium.

The British Journal of Oral & Maxillofacial Surgery
|June 4, 2019
PubMed

Keywords:
embolotherapygluehemorrhagepostoperativesurgically assisted rapid palatal expansion

More Related Videos

TAPE: A Biodegradable Hemostatic Glue Inspired by a Ubiquitous Compound in Plants for Surgical Application08:40

TAPE: A Biodegradable Hemostatic Glue Inspired by a Ubiquitous Compound in Plants for Surgical Application

Published on: June 8, 2016

14.7K
Occlusion of the Great and Small Saphenous Vein Using Copolymeric Glue Based on N-Butyl Cyanoacrylate and Methacryloxy Sulfolane08:05

Occlusion of the Great and Small Saphenous Vein Using Copolymeric Glue Based on N-Butyl Cyanoacrylate and Methacryloxy Sulfolane

Published on: December 9, 2022

5.0K

Related Concept Videos

Bleeding in Fresh Concrete01:22

Bleeding in Fresh Concrete

Bleeding in fresh concrete occurs when water from the mix rises to the surface. This happens because the mix's solid components fail to retain all the water as they settle, leading to separation where water collects at the top. The severity of bleeding can be measured by assessing the total settlement or by noting the decrease in height per unit height of concrete.
Bleeding can cause several issues in the concrete structure. Sometimes, the rising water gets trapped beneath large aggregate...
557
Heat and Free Expansion01:24

Heat and Free Expansion

The work done by a thermodynamic system depends not only on the initial and final states but also on the intermediate states—that is, on the path. Like work, when heat is added to a thermodynamic system, it undergoes a change of state, and the state attained depends on the path from the initial state to the final state. Consider an ideal gas cylinder fitted with a piston. When the cylinder is heated at a constant temperature, the gas molecules absorb energy and expand slowly in a...
2.8K
Thermal Expansion01:22

Thermal Expansion

The expansion of alcohol in a thermometer is one of many commonly encountered examples of thermal expansion, which is the change in size or volume of a given system as its temperature changes. The most visible example is the expansion of hot air. When air is heated, it expands and becomes less dense than the surrounding air, which then exerts an upward force on the hot air to, for example, make steam and smoke rise, and hot air balloons float. The same behavior happens in all liquids and gases,...
5.6K
Expansion and Contraction in Masonry Walls01:19

Expansion and Contraction in Masonry Walls

Masonry walls are subject to slight expansion and contraction due to variations in temperature and moisture. Thermal movement in masonry is relatively straightforward to measure and plan for. On the other hand, moisture movement poses more of a challenge. New clay masonry units typically absorb water and expand over time under normal environmental conditions. Conversely, new concrete masonry units tend to shrink as they lose the excess moisture acquired during their production process.
To...
1.3K
Thermal expansion and Thermal stress: Problem Solving01:27

Thermal expansion and Thermal stress: Problem Solving

San Francisco's Golden Gate Bridge is exposed to temperatures ranging from -15 °C to 40 °C. At its coldest, the main span of the bridge is 1275 m long. Assuming that the bridge is made entirely of steel, what is the change in its length between these temperatures?
To solve the problem, first, identify the known and unknown quantities. The initial length (L) of the bridge is 1275 m, the coefficient of linear expansion (α) for steel is 12 x 10-6/°C, and the change in temperature (ΔT) is 55...
2.1K
Inverse z-Transform by Partial Fraction Expansion01:20

Inverse z-Transform by Partial Fraction Expansion

The inverse z-transform is a crucial technique for converting a function from its z-domain representation back to the time domain. One effective method for finding the inverse z-transform is the Partial Fraction Method, which involves decomposing a function into simpler fractions with distinct coefficients. These fractions correspond to known z-transform pairs, facilitating the inverse transformation process.
To begin the process, the poles of the function are identified and the function is...
689