Related Experiment Video

Updated: Jan 21, 2026

Biofunctionalized Prussian Blue Nanoparticles for Multimodal Molecular Imaging Applications
11:28

Biofunctionalized Prussian Blue Nanoparticles for Multimodal Molecular Imaging Applications

Published on: April 28, 2015

10.8K

Structure and thermal expansion of the distorted Prussian blue analogue RbCuCo(CN)6

Hanna L B Boström1, Ronald I Smith

  • 1Department of Chemistry, Ångström Laboratory, Uppsala University, Box 538, 751 21 Uppsala, Sweden. hanna.bostrom@kemi.uu.se.

Chemical Communications (Cambridge, England)
|August 6, 2019
PubMed

More Related Videos

Rapid One-step Enzymatic Synthesis and All-aqueous Purification of Trehalose Analogues09:27

Rapid One-step Enzymatic Synthesis and All-aqueous Purification of Trehalose Analogues

Published on: February 17, 2017

10.7K
Detection of Architectural Distortion in Prior Mammograms via Analysis of Oriented Patterns13:44

Detection of Architectural Distortion in Prior Mammograms via Analysis of Oriented Patterns

Published on: August 30, 2013

43.6K

Related Concept Videos

Thermal Expansion01:22

Thermal Expansion

The expansion of alcohol in a thermometer is one of many commonly encountered examples of thermal expansion, which is the change in size or volume of a given system as its temperature changes. The most visible example is the expansion of hot air. When air is heated, it expands and becomes less dense than the surrounding air, which then exerts an upward force on the hot air to, for example, make steam and smoke rise, and hot air balloons float. The same behavior happens in all liquids and gases,...
5.6K
Thermal expansion and Thermal stress: Problem Solving01:27

Thermal expansion and Thermal stress: Problem Solving

San Francisco's Golden Gate Bridge is exposed to temperatures ranging from -15 °C to 40 °C. At its coldest, the main span of the bridge is 1275 m long. Assuming that the bridge is made entirely of steel, what is the change in its length between these temperatures?
To solve the problem, first, identify the known and unknown quantities. The initial length (L) of the bridge is 1275 m, the coefficient of linear expansion (α) for steel is 12 x 10-6/°C, and the change in temperature (ΔT) is 55...
2.1K
¹H NMR: Interpreting Distorted and Overlapping Signals01:02

¹H NMR: Interpreting Distorted and Overlapping Signals

Spin systems where the difference in chemical shifts of the coupled nuclei is greater than ten times J are called first-order spin systems. These nuclei are weakly coupled, and their chemical shifts and coupling constant can generally be estimated from the well-separated signals in the spectrum.
As Δν decreases and the signals move closer, the doublets appear increasingly distorted. The intensities of the inner lines increase at the cost of those of the outer lines as the signals are...
1.5K
Heat and Free Expansion01:24

Heat and Free Expansion

The work done by a thermodynamic system depends not only on the initial and final states but also on the intermediate states—that is, on the path. Like work, when heat is added to a thermodynamic system, it undergoes a change of state, and the state attained depends on the path from the initial state to the final state. Consider an ideal gas cylinder fitted with a piston. When the cylinder is heated at a constant temperature, the gas molecules absorb energy and expand slowly in a...
2.8K
Thermal Strain01:19

Thermal Strain

Thermal strain is a concept that arises when we consider how temperature changes affect structures. Unlike the conventional assumption that structures remain constant under load, real-world scenarios often involve temperature fluctuations that can significantly impact these structures. Consider a homogeneous rod with a uniform cross-section resting freely on a flat horizontal surface. If the rod's temperature increases, the rod elongates. This elongation is proportional to the temperature...
2.8K
Thermal Stress01:09

Thermal Stress

If the temperature of an object is changed while it is prevented from expanding or contracting, the object is subjected to stress. The stress is compressive if the object expands in the absence of constraint and tensile if it contracts. This stress resulting from temperature change is known as thermal stress. It can be quite large and can cause damage. To avoid this stress, engineers may design components so they can expand and contract freely. For instance, on highways, gaps are deliberately...
3.3K