Related Experiment Video

Updated: Jan 4, 2026

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes
06:34

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes

Published on: January 6, 2023

3.0K

Experimental data used to validate the FE model of the structural performance of two flexible pipes laid in a single

Alaa Abbas1, Felicite Ruddock2, Rafid Alkhaddar2

  • 1Department of Civil Engineering, Liverpool John Moores University, Henry Cotton Building, 15-21 Webster Street, Liverpool, L3 2ET, UK.

Data in Brief
|November 2, 2019
PubMed

Keywords:
Experimental dataFE model of buried pipesNovel configurationSewer systemSoil-pipe interaction

More Related Videos

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials11:28

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials

Published on: May 18, 2015

12.9K
Mechanical Expansion of Steel Tubing as a Solution to Leaky Wellbores09:32

Mechanical Expansion of Steel Tubing as a Solution to Leaky Wellbores

Published on: November 20, 2014

12.6K

Related Concept Videos

Bending of Material: Problem Solving01:09

Bending of Material: Problem Solving

In this lesson, determine the ratio of the maximum bending moments applied to two metal pipes, given that both pipes can withstand a maximum stress of 100 MPa. Both pipes have an outer radius of 1.8 cm. Pipe A has an inner radius of 1.5 cm, and Pipe B has an inner radius of 1 cm. The ratio of the maximum bending moment applied to two metallic pipes, each with a different inner and outer radius, is determined by considering their dimensions. The inner radius of the first pipe is 1.5 cm, and for...
458
Typical Model Studies01:30

Typical Model Studies

Fluid mechanics model studies often utilize scaled-down systems to predict fluid behavior in full-scale environments, such as river flows, dam spillways, and structures interacting with open surfaces. Maintaining Froude number similarity in river models is crucial, as it replicates surface flow features like wave patterns and velocities.
583
Major Losses in Pipes01:28

Major Losses in Pipes

When a fluid flows through a pipe, it experiences energy losses due to frictional resistance along the pipe walls, known as major losses. These energy losses result in a pressure drop, which varies based on the flow conditions — whether laminar or turbulent — and the specific physical properties of the fluid and pipe.
Fluid flow can be classified as laminar or turbulent, primarily based on the Reynolds number. This dimensionless number reflects the relative influence of inertial to viscous...
1.8K
Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
406
Application of the Linear Momentum Equation01:15

Application of the Linear Momentum Equation

The application of the linear momentum equation can be used to analyze the forces needed to hold a 180-degree pipe bend in place with flowing water. In this case, water flows through the bend with a constant cross-sectional area of 0.01 square meters and a flow velocity of 15 meters per second. The pressure at the entrance is 0.2 Megapascals and the pressure at the exit is 0.16 Megapascals.
The goal is to determine the force components in the x and y directions to hold the pipe in place. Since...
371
Bending of Members Made of Several Materials01:11

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
523