Related Experiment Video

Updated: Jan 1, 2026

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids
11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

8.9K

Induced correlations and rupture of molecular chaos by anisotropic dissipative Janus hard disks

Antonio Lasanta1,2,3, Aurora Torrente1, Mariano López de Haro2

  • 1Gregorio Millán Institute of Fluid Dynamics, Nanoscience and Industrial Mathematics, Department of Materials Science and Engineering and Chemical Engineering, Universidad Carlos III de Madrid, 28911 Leganés, Spain.

Physical Review. E
|December 25, 2019
PubMed

More Related Videos

Predicting Catalyst Extrudate Breakage Based on the Modulus of Rupture09:53

Predicting Catalyst Extrudate Breakage Based on the Modulus of Rupture

Published on: May 13, 2018

8.6K
Magnetically Induced Rotating Rayleigh-Taylor Instability06:42

Magnetically Induced Rotating Rayleigh-Taylor Instability

Published on: March 3, 2017

10.0K

Related Concept Videos

Elastic Strain Energy for Shearing Stresses01:20

Elastic Strain Energy for Shearing Stresses

As discussed in previous lessons, strain energy in a material is the energy stored when it is elastically deformed, a concept crucial in materials science and mechanical engineering. This energy results from the internal work done against the cohesive forces within the material. When a material undergoes shearing stress and corresponding shearing strain, the strain energy density, which is the energy stored per unit volume, is calculated. Within the elastic limit, where the stress is...
446
Entropy Change in Reversible Processes01:10

Entropy Change in Reversible Processes

In the Carnot engine, which achieves the maximum efficiency between two reservoirs of fixed temperatures, the total change in entropy is zero. The observation can be generalized by considering any reversible cyclic process consisting of many Carnot cycles. Thus, it can be stated that the total entropy change of any ideal reversible cycle is zero.
The statement can be further generalized to prove that entropy is a state function. Take a cyclic process between any two points on a p-V diagram.
3.1K
Entropy and the Second Law of Thermodynamics01:20

Entropy and the Second Law of Thermodynamics

The second law of thermodynamics can be stated quantitatively using the concept of entropy. Entropy is the measure of disorder of the system.
The relation  between entropy and disorder can be illustrated with the example of the phase change of ice to water. In ice, the molecules are located at specific sites giving a solid state, whereas, in a liquid form, these molecules are much freer to move. The molecular arrangement has therefore become more randomized. Although the change in average...
4.7K
Theories of Dissolution: The Danckwerts' Model and Interfacial Barrier Model01:09

Theories of Dissolution: The Danckwerts' Model and Interfacial Barrier Model

Various dissolution theories provide insight into the factors that influence the dissolution rate. Danckwerts' Model suggests that turbulence, rather than a stagnant layer, characterizes the dissolution medium at the solid-liquid interface. In this model, the agitated solvent contains macroscopic packets that move to the interface via eddy currents, facilitating the absorption and delivery of the drug to the bulk solution. The regular replenishment of solvent packets maintains the...
713
Magnetic Damping01:17

Magnetic Damping

Eddy currents can produce significant drag on motion, called magnetic damping. For instance, when a metallic pendulum bob swings between the poles of a strong magnet, significant drag acts on the bob as it enters and leaves the field, quickly damping the motion.
If, however, the bob is a slotted metal plate, the magnet produces a much smaller effect. When a slotted metal plate enters the field, an emf is induced by the change in flux; however, it is less effective because the slots limit the...
965
Shearing Strain01:20

Shearing Strain

The shearing strain represents a cubic element's angular change when subjected to shearing stress. This type of stress can transform a cube into an oblique parallelepiped without influencing normal strains. The cubic element experiences a significant transformation when exposed solely to shearing stress. Its shape alters from a perfect cube into a rhomboid, clearly demonstrating the effect of shearing strain. The degree of this strain is considered positive if it reduces the angle between the...
1.1K