Life-cycle inventory data and impacts on electricity production at the United Downs Deep Geothermal Power project in

Related Experiment Video

Updated: Dec 29, 2025

Operation of a 25 KWth Calcium Looping Pilot-plant with High Oxygen Concentrations in the Calciner
06:34

Operation of a 25 KWth Calcium Looping Pilot-plant with High Oxygen Concentrations in the Calciner

Published on: October 25, 2017

8.3K

Andrea Paulillo1, Lucy Cotton2, Ryan Law2

  • 1Department of Chemical Engineering, University College London, Torrington Place, London, WC1 E7JE, United Kingdom.

Data in Brief
|January 29, 2020
PubMed

Keywords:
Enhanced geothermal systemsEnvironmental impactsGeothermal energyInventoryLife cycle assessment

More Related Videos

Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions08:18

Design and Use of a Full Flow Sampling System FFS for the Quantification of Methane Emissions

Published on: June 12, 2016

17.2K
Measuring Carbon-based Contaminant Mineralization Using Combined CO2 Flux and Radiocarbon Analyses11:19

Measuring Carbon-based Contaminant Mineralization Using Combined CO2 Flux and Radiocarbon Analyses

Published on: October 21, 2016

12.3K

Related Concept Videos

Energy Line and Hydraulic Gradient Line01:27

Energy Line and Hydraulic Gradient Line

Based on Bernoulli's equation, the energy line (EL) and hydraulic grade line (HGL) provide graphical representations of energy distribution in a fluid flow system. For steady, incompressible, inviscid flows, Bernoulli's equation is expressed as:
1.9K
Nuclear Power02:36

Nuclear Power

Controlled nuclear fission reactions are used to generate electricity. Any nuclear reactor that produces power via the fission of uranium or plutonium by bombardment with neutrons has six components: nuclear fuel consisting of fissionable material, a nuclear moderator, a neutron source, control rods, reactor coolant, and a shield and containment system.
Nuclear Fuels
Nuclear fuel consists of a fissile isotope, such as uranium-235, which must be present in sufficient quantity to provide a...
9.2K
Power in a Three-Phase Circuit01:15

Power in a Three-Phase Circuit

Three-phase systems have two configurations: the wye and delta. A star configuration can be three or four wires; in a delta configuration, the components are connected in a closed loop. Instantaneous power refers to the power value at a precise moment, and in a balanced three-phase system, it is constant. This is because the sum of the instantaneous powers in the three phases remains steady over time, despite individual fluctuations, due to the symmetry and phase relationship. The total...
549
Energy Diagrams - I01:14

Energy Diagrams - I

The dynamics of a mechanical system can be easily understood by interpreting a potential energy diagram. Since energy is a scalar quantity, the interpretation of the dynamics of the system becomes even simpler.
Take the example of a skater on a parabolic ramp. The potential energy at different points along the ramp will be proportional to the height of the ramp, which varies quadratically with the horizontal position on the ramp. As the skater moves down the ramp from the highest position,...
5.5K
Electrical Energy01:10

Electrical Energy

Using electric appliances for a longer period of time consumes more electrical energy and results in a higher electric bill. The energy produced by the transfer of electrons from one point to another is known as electrical energy. If power is delivered at a constant rate, the electrical energy can be defined as the product of power used by the device for a period of time. The energy unit on electric bills is the kilowatt-hour, where one kilowatt-hour is equivalent to 3.6 × 106 joules.
1.6K
Energy Diagrams - II01:10

Energy Diagrams - II

Energy diagrams are important to understand the dynamics of a system. The topology of an energy diagram helps illustrate the equilibrium points of the system.
The point in the energy diagram at which the system’s potential energy is the lowest is known as the local minima. The system tends to stay in this position indefinitely unless acted upon by a net force. The slope of the potential energy diagram at the local minima is zero, indicating that zero net force is acting on the system. The...
11.7K