Related Experiment Video

Updated: Dec 27, 2025

Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes
06:56

Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes

Published on: May 23, 2017

12.6K

Moiré patterns in non-parallel surfaces such as wedge

Vladimir Saveljev, Jung-Young Son, Yongsuk Kim

    Journal of the Optical Society of America. A, Optics, Image Science, and Vision
    |March 3, 2020
    PubMed

    More Related Videos

    Optimized Fabrication Procedure for High-Quality Graphene-based Moiré Superlattice Devices11:24

    Optimized Fabrication Procedure for High-Quality Graphene-based Moiré Superlattice Devices

    Published on: July 11, 2025

    14.3K
    Scalable Stamp Printing and Fabrication of Hemiwicking Surfaces06:16

    Scalable Stamp Printing and Fabrication of Hemiwicking Surfaces

    Published on: December 18, 2018

    7.6K

    Related Concept Videos

    Interference and Diffraction02:18

    Interference and Diffraction

    Interference is a characteristic phenomenon exhibited by waves. When two electromagnetic waves interact with their peaks and troughs coinciding, a resulting wave with enhanced amplitude is produced. This is known as constructive interference. In this case, the two waves interacting are in phase with each other.
    51.3K
    Mohr's Circle for Plane Strain01:18

    Mohr's Circle for Plane Strain

    Mohr's circle is a crucial graphical method used to analyze plane strain by plotting strain on a set of cartesian coordinates, where the abscissa is normal strain ∈ and the ordinate is shear strain γ. Similarly to Mohr’s circle for plane stress, two points X and Y are plotted. Their coordinates are (∈x, -γXY) and (∈Y, γXY), respectively.
    Mohr's circle visually represents the strain states under various conditions, which is essential for...
    1.1K
    Mohr's Circle for Plane Stress01:23

    Mohr's Circle for Plane Stress

    Mohr's circle is a graphical method for identifying the state of stress at a point in a material, making it easier to analyze stress transformations under plane stress conditions. This two-dimensional technique visualizes both normal and shearing stresses on an element.
    Consider a set of Cartesian coordinates. The horizontal and vertical axes correspond to normal stress (σ) and shearing stress (τ), respectively. Two points, points A and B, are defined by the normal and shear...
    1.0K
    Plastic Deformations of Members with a Single Plane of Symmetry01:21

    Plastic Deformations of Members with a Single Plane of Symmetry

    When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
    293
    Wood Surfacing01:14

    Wood Surfacing

    Wood surfacing is a critical finishing process designed to smoothen the wood surface, enhance its dimensional accuracy, and make handling safer. This process compensates for potential shrinkage during the seasoning phase by marginally increasing the wood dimensions before surfacing. It also helps correct some distortions that may occur as the wood dries.
    The equipment used in the surfacing process is a plane equipped with rotating blades. This tool efficiently smoothens the wood surface and can...
    285
    Gauss's Law: Planar Symmetry01:27

    Gauss's Law: Planar Symmetry

    A planar symmetry of charge density is obtained when charges are uniformly spread over a large flat surface. In planar symmetry, all points in a plane parallel to the plane of charge are identical with respect to the charges. Suppose the plane of the charge distribution is the xy-plane, and the electric field at a space point P with coordinates (x, y, z) is to be determined. Since the charge density is the same at all (x, y) - coordinates in the z = 0 plane, by symmetry, the electric field at P...
    9.2K