Related Experiment Video

Updated: Dec 21, 2025

Manufacturing Simple and Inexpensive Soil Surface Temperature and Gravimetric Water Content Sensors
08:49

Manufacturing Simple and Inexpensive Soil Surface Temperature and Gravimetric Water Content Sensors

Published on: December 21, 2019

9.9K

Lead-Wire-Resistance Compensation Technique Using a Single Zener Diode for Two-Wire Resistance Temperature Detectors

Wei Li1, Shusheng Xiong2, Xiaojun Zhou1

  • 1School of Mechanical Engineering, Zhejiang University, Hangzhou 310027, China.

Sensors (Basel, Switzerland)
|May 15, 2020
PubMed

Keywords:
RTDlead wiretemperature measurementzener diode

More Related Videos

Construction of a Wireless-Enabled Endoscopically Implantable Sensor for pH Monitoring with Zero-Bias Schottky Diode-based Receiver08:25

Construction of a Wireless-Enabled Endoscopically Implantable Sensor for pH Monitoring with Zero-Bias Schottky Diode-based Receiver

Published on: August 27, 2021

2.9K
Thermal Measurement Techniques in Analytical Microfluidic Devices08:29

Thermal Measurement Techniques in Analytical Microfluidic Devices

Published on: June 3, 2015

10.0K

Related Concept Videos

Zener Diodes01:16

Zener Diodes

Zener diodes are specialized semiconductor devices designed to operate in the reverse breakdown region, where they allow current to flow into the cathode, making it positive relative to the anode. This reverse operation distinguishes Zener diodes from conventional diodes and enables their use in various applications, most notably as voltage regulators. One of the defining characteristics of Zener diodes is their nearly vertical I-V (current-voltage) characteristic curve above a certain...
980
Thermal expansion and Thermal stress: Problem Solving01:27

Thermal expansion and Thermal stress: Problem Solving

San Francisco's Golden Gate Bridge is exposed to temperatures ranging from -15 °C to 40 °C. At its coldest, the main span of the bridge is 1275 m long. Assuming that the bridge is made entirely of steel, what is the change in its length between these temperatures?
To solve the problem, first, identify the known and unknown quantities. The initial length (L) of the bridge is 1275 m, the coefficient of linear expansion (α) for steel is 12 x 10-6/°C, and the change in temperature (ΔT) is 55...
2.0K
Resistance and Conductance01:25

Resistance and Conductance

A conductor's DC resistance at a given temperature is influenced by its resistivity, length, and cross-sectional area. Resistivity is an inherent property of the conductor material, with annealed copper serving as the international standard for measurement. For instance, the resistivity of hard-drawn aluminum at 20 degrees Celsius is 61% of the standard conductivity of annealed copper.
Various factors impact the resistance of a conductor. Spiraling in stranded conductors increases their...
426
Resistance01:19

Resistance

When a current moves through any conductor, the conductor causes some level of difficulty for the current to flow. The measure of that difficulty is known as the resistance of the material and is represented by R. Every material has its own resistance. In the case of conductors, heat is emitted whenever a current passes through them. Resistance depends on the resistivity of the material. Resistivity is a characteristic of the material used to fabricate electrical components, whereas the...
5.6K
Modeling of Diode Reverse Characteristics01:14

Modeling of Diode Reverse Characteristics

In electronic circuits, reverse-biased diode configurations are critical for regulating voltage levels. Zener diodes exploit the reverse breakdown phenomenon and exhibit a controlled breakdown at a specific Zener voltage (VZ). They are designed to maintain a constant voltage across their terminals and are commonly used for voltage regulation in circuits.
When a reverse voltage applied to a Zener diode exceeds its breakdown voltage, the diode enters the breakdown region. At this point, the...
542
Design Example: Strain Gauge Bridge or Wheatstone Bridge01:15

Design Example: Strain Gauge Bridge or Wheatstone Bridge

The utilization of strain gauges as transducers for converting mechanical strain into electrical signals is a common practice in various engineering applications. These strain gauges are frequently integrated into Wheatstone bridge circuits to accurately measure parameters such as force or pressure. Within this context, each element within the circuit exhibits a resistance that undergoes subtle variations when subjected to mechanical strain. The primary objective is to convert minuscule...
846