Related Experiment Video

Updated: Jul 25, 2026

Mimicking and Measuring Occlusal Erosive Tooth Wear with the "Rub&Roll" and Non-contact Profilometry
08:47

Mimicking and Measuring Occlusal Erosive Tooth Wear with the "Rub&Roll" and Non-contact Profilometry

Published on: February 2, 2018

12.6K

Effect of contact characteristics on the self-rotation performance of conical picks based on impact dynamics

Xiaohui Liu1,2, Qi Geng1

  • 1Key Laboratory of Road Construction Technology and Equipment of MOE, School of Construction Machinery, Chang'an University, Xi'an 710064, People's Republic of China.

Royal Society Open Science
|June 16, 2020
PubMed

Keywords:
conical pickimpact dynamicsrockself-rotationwear

More Related Videos

Addressing Practical Issues in Atomic Force Microscopy-Based Micro-Indentation on Human Articular Cartilage Explants08:06

Addressing Practical Issues in Atomic Force Microscopy-Based Micro-Indentation on Human Articular Cartilage Explants

Published on: October 28, 2022

1.3K
Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid08:58

Atomic Force Microscopy Cantilever-Based Nanoindentation: Mechanical Property Measurements at the Nanoscale in Air and Fluid

Published on: December 2, 2022

3.6K

Related Concept Videos

Impact01:30

Impact

Impact occurs when two bodies collide, leading to the application of impulsive forces between them. Analyzing impact mechanics involves considering two colliding particles moving along a line known as the line of impact, which passes through their centers and is perpendicular to the contact plane.
When particles with different initial velocities collide, they induce deformation by applying equal and opposite impulses. At the point of maximum deformation, the particles move together with...
Impact: Problem Solving01:26

Impact: Problem Solving

In an experiment conducted during a Mars mission, a rover propels a projectile with an initial velocity, and the projectile rebounds after colliding with the Martian surface. To ascertain the maximum height attained by the projectile after this collision, the known restitution coefficient and acceleration due to gravity are employed.
By designating the launch point as the origin and utilizing kinematic equations, the vertical component of the projectile's velocity at the point of impact is...
Principle of Angular Impulse and Momentum: Problem Solving01:19

Principle of Angular Impulse and Momentum: Problem Solving

Consider a ball of mass m, attached to a massless rod of known length, subjected to a time-dependent torque. If the initial velocity of the mass is known, then the final velocity of the mass for time t can be determined using the principle of angular impulse and momentum.
Initially, a free-body diagram of the system is drawn to illustrate all the forces acting upon the system, providing a crucial understanding of the dynamics at play. Then, the principle of angular impulse and momentum is...
Angle of Twist: Problem Solving01:13

Angle of Twist: Problem Solving

An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the torque exerted...
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the shaft's...
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...