Related Experiment Video

Updated: Dec 11, 2025

Characterization of Anisotropic Leaky Mode Modulators for Holovideo
09:36

Characterization of Anisotropic Leaky Mode Modulators for Holovideo

Published on: March 19, 2016

8.2K

Design of a non-Hermitian on-chip mode converter using phase change materials

Song-Rui Yang, Xu-Lin Zhang, Hong-Bo Sun

    Optics Letters
    |August 16, 2020
    PubMed

    More Related Videos

    In Situ Transmission Electron Microscopy with Biasing and Fabrication of Asymmetric Crossbars Based on Mixed-Phased a-VOx09:49

    In Situ Transmission Electron Microscopy with Biasing and Fabrication of Asymmetric Crossbars Based on Mixed-Phased a-VOx

    Published on: May 13, 2020

    4.3K
    Merging Ion Concentration Polarization between Juxtaposed Ion Exchange Membranes to Block the Propagation of the Polarization Zone08:06

    Merging Ion Concentration Polarization between Juxtaposed Ion Exchange Membranes to Block the Propagation of the Polarization Zone

    Published on: February 23, 2017

    8.8K

    Related Concept Videos

    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    1.3K
    MOSFET: Enhancement Mode01:22

    MOSFET: Enhancement Mode

    Enhancement-mode MOSFETs are pivotal components in electronics, distinguished by their capacity to act as highly efficient switches. They are part of the larger family of metal-oxide Semiconductor Field-Effect Transistors (MOSFETs). They are available in two types: p-channel and n-channel, each tailored to specific polarity operations.
    In their basic form, enhancement-mode MOSFETs are typically non-conductive when the gate-source voltage (Vgs) is zero. This default 'off' state means no...
    670
    Biasing of Metal-Semiconductor Junctions01:27

    Biasing of Metal-Semiconductor Junctions

    Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
    In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
    459
    MOSFET: Depletion Mode01:20

    MOSFET: Depletion Mode

    Depletion-mode MOSFETs represent a unique subset of MOSFET technology, functioning fundamentally differently from their enhancement-mode counterparts. Unlike enhancement MOSFETs, which require a positive gate-source voltage (Vgs) to turn on, depletion-mode MOSFETs are inherently conductive and "normally on" devices.
    The primary characteristic of depletion-mode MOSFETs is their ability to conduct current between the drain and source terminals without gate bias. This inherent conductivity...
    710
    Non-ohmic Devices00:51

    Non-ohmic Devices

    In most substances, the current flow is proportional to the voltage applied to it. A simple relationship between the values of current, voltage, and resistance is known as Ohm's law. Nonohmic devices do not exhibit a linear relationship between voltage and current. One such device is the semiconducting circuit element known as a diode. A diode is a circuit device that allows current flow in only one direction.
    Consider a simple circuit consisting of a battery, a diode, and a resistor. A...
    1.4K
    Phase Changes01:19

    Phase Changes

    Phase transitions play an important theoretical and practical role in the study of heat flow. In melting or fusion, a solid turns into a liquid; the opposite process is freezing. In evaporation, a liquid turns into a gas; the opposite process is condensation.
    A substance melts or freezes at a temperature called its melting point and boils or condenses at its boiling point. These temperatures depend on pressure. High pressure favors the denser form of the substance, so typically, high pressure...
    5.1K