Related Experiment Video

Updated: Dec 7, 2025

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators
11:44

Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators

Published on: August 15, 2014

10.7K

Study of the Influence of Phase Noise on the MEMS Disk Resonator Gyroscope Interface Circuit

Wenbo Zhang1, Weiping Chen1,2, Liang Yin1,2

  • 1MEMS Center, Harbin Institute of Technology, Harbin 150000, China.

Sensors (Basel, Switzerland)
|September 29, 2020
PubMed

Keywords:
bias stabilitydisk resonator gyroscopegyroscope interface circuitphase noise

More Related Videos

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters15:25

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

Published on: February 4, 2018

6.4K
Fabrication and Characterization of High-Q Silicon Nitride Membrane Resonators09:46

Fabrication and Characterization of High-Q Silicon Nitride Membrane Resonators

Published on: August 8, 2025

925

Related Concept Videos

NMR Spectrometers: Resolution and Error Correction01:14

NMR Spectrometers: Resolution and Error Correction

When magnetic nuclei in a sample achieve resonance and undergo relaxation, the signal detected in NMR is an approximately exponential free induction decay. Fourier transform of an exponential decay yields a Lorentzian peak in the frequency domain. Lorentzian peaks in an NMR spectrum are defined by their amplitude, full width at half maximum, and position, where the peak width is governed by the spin-spin relaxation time alone. In real experiments, however, the applied magnetic field is rendered...
962
Biasing of FET01:22

Biasing of FET

Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the...
546
Oscillations In An LC Circuit01:30

Oscillations In An LC Circuit

An idealized LC circuit of zero resistance can oscillate without any source of emf by shifting the energy stored in the circuit between the electric and magnetic fields. In such an LC circuit, if the capacitor contains a charge q before the switch is closed, then all the energy of the circuit is initially stored in the electric field of the capacitor. This energy is given by
2.8K
Time and frequency -Domain Interpretation of Phase-lead Control01:24

Time and frequency -Domain Interpretation of Phase-lead Control

Phase-lead controllers are commonly used in various control systems to enhance response speed and stability. Adjusting the brightness on a television screen offers a practical example of phase-lead control. When contrast is enhanced, a phase-lead controller is employed. Mathematically, phase-lead control is identified when the first parameter is smaller than the second.
The design of phase-lead control involves the strategic placement of poles and zeros to balance steady-state error and system...
349
Resonance in an AC Circuit01:26

Resonance in an AC Circuit

The property of an inductor makes it resist any change in the current passing through it, while the property of a capacitor is to build up the charge across its terminals. Hence, if an inductor and capacitor are connected in series, they have opposite effects on the relative phase between current and voltage. The current through the circuit undergoes forced oscillation at the frequency of the source. The resistance term in an R-L-C circuit acts as a damping term because power is dissipated...
2.3K
Time and frequency -Domain Interpretation of Phase-lag Control01:21

Time and frequency -Domain Interpretation of Phase-lag Control

Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any...
321