Related Experiment Video

Updated: Nov 27, 2025

Measurement of the Hand Transmitted Vibration of the Human Hand Arm System During Operation of a Hand Tractor
09:35

Measurement of the Hand Transmitted Vibration of the Human Hand Arm System During Operation of a Hand Tractor

Published on: June 16, 2021

4.7K

Whole-body Vibration Exposure Experienced by Dumper Operators in Opencast Mining According to ISO 2631-1:1997 and ISO

Shivkumar Shrinarayan Prajapati1, Rahul Anup Mishra1, Balram Jhariya1

  • 1Department of Occupational Hygiene, National Institute of Miners Health (Ministry of Mines, Government of India), JNARDDC Campus, Amravati Road, Wadi, Nagpur, Maharashtra, India.

Indian Journal of Occupational and Environmental Medicine
|December 7, 2020
PubMed

Keywords:
Health riskminingoccupational healthwhole-body vibration

More Related Videos

Whole Body Vibration Methods with Survivors of Polio04:16

Whole Body Vibration Methods with Survivors of Polio

Published on: October 17, 2018

9.0K
Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior10:52

Simulation of Human-induced Vibrations Based on the Characterized In-field Pedestrian Behavior

Published on: April 13, 2016

9.0K

Related Concept Videos

Vibrating Concrete01:19

Vibrating Concrete

Mechanical vibrators are instrumental in compacting newly poured concrete within formwork and around reinforcements. This process is essential to eliminate trapped air pockets and establish a dense concrete mass. One widely used method is vibrating by internal vibrators, often referred to as a poker vibrator or immersion vibrator. It is rapidly inserted through the full depth of the freshly laid concrete and slightly extends into the layer below it (which remains in a plastic state). Consistent...
256
Slump Test01:20

Slump Test

The slump test is a widely used method to measure the workability of concrete. It employs a 12-inch high truncated cone mold that tapers from eight inches at the base to four inches at the top. Before testing, the mold is securely attached to a flat base and dampened.
Concrete is poured into the mold in three layers to conduct the test. Each layer is compacted 25 times with a steel tamping rod, which has a five-eighths-inch diameter and a rounded end, to ensure even distribution and eliminate...
609
Abrasion Resistance of Concrete01:23

Abrasion Resistance of Concrete

Abrasion resistance is an essential characteristic of concrete that determines its durability and longevity under various wear conditions. Concrete surfaces are vulnerable to different types of abrasion. For instance, surfaces may wear down due to the constant movement of vehicles or be eroded by solids carried in water, as seen in concrete canal linings. Specific tests are conducted to measure the abrasion resistance of concrete.
One such test is the revolving disc test, where three plates...
354
Unsoundness of Aggregate due to Volume Change01:26

Unsoundness of Aggregate due to Volume Change

Unsoundness in aggregates due to volume changes is primarily caused by the physical alterations aggregates undergo, such as freezing and thawing, thermal changes, and wetting and drying. Unsound aggregates, when subjected to these changes, result in volume change upon disintegration. This, in turn, contributes to the deterioration of concrete, including scaling, pop-outs, and cracking. Particular types of aggregates, such as porous flints, cherts, and those containing clay minerals, are...
273
Quarrying of Stone01:15

Quarrying of Stone

Quarrying is the process of extracting stone from a quarry, where specialized techniques are employed to remove large blocks of stone safely and efficiently. This process can involve controlled explosions or more precision-oriented methods such as cutting and drilling.
One common method involves using a diamond belt saw to cut large blocks from the quarry face. These blocks can be about 50 feet long and 12 feet high. After the initial vertical cut, drilling is performed at the base of the...
329
Dynamic Modulus of Elasticity of Concrete01:16

Dynamic Modulus of Elasticity of Concrete

The dynamic modulus of elasticity assesses how a concrete structure deforms under impact or dynamic loads. It is typically higher than the static modulus of elasticity, measured under slow, steady loading conditions.
The sonic test is a common method to determine the dynamic modulus. In this test, a concrete beam, sized either 6 x 6 x 30 inches or 4 x 4 x 20 inches, is clamped at its center. Vibrations are initiated at one end of the beam by an electromagnetic exciter unit powered by a...
715