Related Experiment Video

Updated: Nov 24, 2025

A Standardized Method for Measurement of Elbow Kinesthesia
07:56

A Standardized Method for Measurement of Elbow Kinesthesia

Published on: October 10, 2020

7.4K

Material Properties of the Medial Elbow During Passive Valgus and Self-Initiated Varus Torques

Brian J Diefenbach1, Anthony S Kulas1, Christopher J Curran1

  • 1East Carolina University.

Journal of Applied Biomechanics
|December 21, 2020
PubMed

Keywords:
UCLelastographyultrasound

More Related Videos

Author Spotlight: Integrating Mechanical and Biological Analysis in Tendinopathy Research04:37

Author Spotlight: Integrating Mechanical and Biological Analysis in Tendinopathy Research

Published on: March 1, 2024

1.2K
Biomechanical Testing of Murine Tendons10:09

Biomechanical Testing of Murine Tendons

Published on: October 15, 2019

13.8K

Related Concept Videos

Circular Shafts - Elastoplastic Materials01:24

Circular Shafts - Elastoplastic Materials

The study of solid circular shafts under stress shows that within the elastic limit, stress increases directly to the distance from the shaft's center. This relationship holds until the shaft reaches a critical point of stress, beyond which it begins to yield, marking the transition from elastic to plastic deformation. At this crucial juncture, the maximum torque the shaft can endure without permanent deformation is determined, signifying the limit of its elastic behavior.
As torque on the...
306
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
261
Strain and Elastic Modulus01:15

Strain and Elastic Modulus

The quantity that describes the deformation of a body under stress is known as strain. Strain is given as a fractional change in either length, volume, or geometry under tensile, volume (also known as bulk), or shear stress, respectively, and is a dimensionless quantity. The strain experienced by a body under tensile or compressive stress is called tensile or compressive strain, respectively. In contrast, the strain experienced under bulk stress and shear stress is known as volume and shear...
6.9K
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
421
Hooke's Law01:26

Hooke's Law

Hooke's law, a pivotal principle in material science, establishes that the strain a material undergoes is directly proportional to the applied stress, defined by a factor called the modulus of elasticity or Young's modulus.
1.0K
Normal Strain under Axial Loading01:20

Normal Strain under Axial Loading

Normal strain under axial loading is an important concept in the field of mechanics of materials. Axial loading implies the application of a force along the axis of a material, like a column or bar. This force can either compress or stretch the material. In the context of axial loading, normal strain is the deformation experienced by the material in the direction of the loading force. It's calculated as the change in length divided by the original length of the material. This unitless ratio...
918